winterizing

[robbym70]

I've got an above ground so my situation is different but some things are universal I would guess.

I have a solid cover as well. I've been using the BBB method since I bought the house with the pool, about three years now. The first year I opened it we had an algae bloom that lasted for 2 or 3 weeks. Since then we've had smooth sailing.

I keep it simple. I add a bottle of polyquat algaecide and 3 or 4 gallons of bleach. Put the air pillow on then the winter cover. I check the water clarity every 2 or 3 weeks until the surface is frozen and then again in the spring. I open early...late April to Mid May and I close late...usually 2nd week in October. That's it. Sometimes I wonder..."what am I missing that those $$ winterizer kits have that I don't"...but the proof is in the pudding.

[JimK]

I've got an above ground so my situation is different but some things are universal I would guess.

I have a solid cover as well. I've been using the BBB method since I bought the house with the pool, about three years now. The first year I opened it we had an algae bloom that lasted for 2 or 3 weeks. Since then we've had smooth sailing.

I keep it simple. I add a bottle of polyquat algaecide and 3 or 4 gallons of bleach. Put the air pillow on then the winter cover. I check the water clarity every 2 or 3 weeks until the surface is frozen and then again in the spring. I open early...late April to Mid May and I close late...usually 2nd week in October. That's it. Sometimes I wonder..."what am I missing that those $$ winterizer kits have that I don't"...but the proof is in the pudding.

I've been using a closing kit since 2004 that worked well. Last year I finally took a closer look to see what was in it; polyquat, stain inhibitor, phosphate remover, and borax. I've learned here that I don't need the phosphate remover, I already have polyquat and stain inhibitor on hand, and I already keep borates in the pool, so this year I'll forgo the kit and simplify the closing process.

Gotta love this forum!

[Shredhead]

I think a lot of your algae problem would be alleviated by closing later and opening earlier. September and May can be fairly warm and probably let's the algae bloom.

I have a mesh covered IG pool I close mid October and open to a fairly clear pool in late April.

[CarlD]

Hi everyone: Been awhile. Sorry about that.
I have an AGP, but in many ways it's more like an IGP, other than the plumbing. So I don't have to blow out lines and fill them with antifreeze, I just remove them. But I have to blow out my solar panels and all of their lines.
I use a mesh safety cover and always have as I'm not directly under any trees. I do follow the 60 deg rule, mostly. In the fall I wait as long as I can for the water to get at least close to 60. By then I've shut down the solar panels and blown them out, and plugged their returns. I clean and shock the pool up to the max for the CYA level, then add a quart of Polyquat 60%. I wait 48 hours for the FC to drop (a reaction to the Polyquat) then boost FC up to shock levels and close. That means lowering the water below the return, or even the lights, plugging the low drain, the skimmer, the overflow and the return.

I can then remove and drain the plumbing behind them. I have quick-connects or quick-connect ball valves everywhere. I disconnect them, dry and lube each o-ring, then put each one in a zip-lock marked with a sharpie. The plumbing is stored in the basement where it's warm and dry, including the pump. The mesh goes on and I'm done till April.

Up here, we get a solid block of ice, sometimes well over a foot thick. When this is all gone, usually in April, I begin to open. IF I get to it that early, I have little or no algae and a fairly simple clean up. If I am later, I have to shock the water to kill the algae that starts. Since my liner is now 11 years old, I don't worry about bleaching it. It's bleached already!

[robbym70]

..... I disconnect them, dry and lube each o-ring....

That is a great idea. A few minutes of extra effort will make those o rings last so much longer...

[apearso]

It's been a fairly warm fall here in PA, wondering if it would help the spring opening if I poured some bleach in through the mesh cover.

[PoolDoc]

With a mesh cover, you need to maintain the water under the cover, all winter long. Pouring bleach through is an excellent way to do so -- but use a hose to rinse off the cover afterwards.