Using HydroPureTech cartridges to deal with Iron

[PoolDoc]

Like I said, we're very open to the possibility of new products that do work . . . so I really do hope you follow up next season with a positive report.

[BJohnston]

Like I said, we're very open to the possibility of new products that do work . . . so I really do hope you follow up next season with a positive report.

Has anyone tried this since last season? Any follow up from anyone or OP? I am on well water and am looking for options to be able to use it to filter my top off water.

Background: My water has been tested 7-8 times from different water people since I moved into my new house this past Oct. with varying results of having traces amounts of iron or having none. I have an old softener (~20 yrs) that seemed to be working but I was in the market for a new one. I can attribute some of these varying results to a old hot water heater, and some iron fittings being used on my system. I have since replace the hot water heater with a new one, which has no effect on my pool fill up, and removed all (except for a couple of special fittings an check valve) of the metal plumbing between my well and softener and replace with PVC.

I have not yet performed a bucket test or had my water retested since the PVC replacement so that's something I need to take care of soon. I just got my K-2000 kit in the mail a few days ago. I'm just doing some homework and saw this post. If in fact I do still have some trace amounts of iron, I would like to filter them out before going into my pool. Currently I have orange/brown steps which I am working out a plan to fix today, hopefully to a minimal degree before a BBQ party tomorrow. I was able to remove most of it previously with HTH metal remover so I know that there is some iron in my pool, probably from the previous owner's top offs.

[PoolDoc]

Do you have a skimmer?

If you do, there's a way to use cal hypo tablets in conjunction with a sand filter to continuously remove iron and other metals.

[BJohnston]

Yes I do. I have been doing more reading and see suggestions to use both Cal Hypo or Tri-Chlor.

I am leaning towards using the Tri-Chlor because my CYA is low and needs replenished. I also have CYA I can add on its own so I'm not sure which way will be the best.

I need to retest my numbers when I get home, I did not get a chance to this morning before heading off to work. what are the upside/down side to using Cal-Hypo vs. Tri-Chlor assuming I need to add CYA anyway?

[PoolDoc]

For dealing with iron, cal hypo is much better. The only downside to cal hypo is that you MUST use it the way I instruct you to do, or your will end up with calcium that is too high. Well, I guess the fact that you may not need as much as you'll have to buy is a downside. It will keep till next year, but will be 'stinky' when you open it next spring

This is the ONLY product I've found that you'd want to use:
CCH Calcium Hypochlorite Tablets 50 lb bucket

The Arch cal hypo tablets contain 25% or more magnesium sulfate, and you don't want that in your pool.

[BJohnston]

Wow, that will be quite an investment. I don't know if my iron issues are that severe to justify the cost currently. Do they have that in any smaller amounts?

My fiberglass steps seem to be the only thing being effected currently. They are orange/brown. I have 1.75 lbs of natural chem stain free, I know its only Citric acid, and could get a better price elsewhere, but I was in a rush and decided to buy it at the local Pool "Steal" while I was there getting some misc fittings and parts. I am going to by a culator 4ppm but haven't clicked the purchase button just yet.

I have a party tomorrow and was going to try to minimize the ugly brown steps and make it look half decent so that people aren't afraid to swim or have everyone ask me the same ???'s about it. I was hoping to just get it managed and then address it permanently afterwards. I know there are a lot of different options that people have used so like I said in the beginning, I'm just trying to do my homework before I go to far in the wrong direction.

I successfully used HTH metal control to reduce/remove the staining (aka put it back into solution) but now its back again. I assume due to high chlorine from shocking recently. So I'm assuming that I can replicate that with the stain free. Am I wandering down the wrong path with this one or can this be an ok start/temp fix?

[PoolDoc]

Do NOT use citric acid.

If you want to re-dissolve the iron, use ascorbic acid. But remember that NEITHER are compatible with chlorine.

You need to get clear on the difference between dissolving iron, and removing iron. The ascorbic acid will help redissolve iron where it has stained surfaces. But it will do NOTHING to actually remove it from the pool -- rather it just *moves* the iron from the stains ON the pool to the water IN the pool.

By contrast, the cal hypo will do NOTHING to help with the stains, but it will enable you to remove the iron that is IN the water.

The expensive of the cal hypo is not an 'extra' expense, like ascorbic acid will be. Rather, it will become THE way you chlorinate. The reason for using it is that WHILE it chlorinates, if you use it correctly, it will ALSO remove iron FROM the pool water and deposit ONTO the calcium dust collected by your filter. From there, both the dust and the iron will be actually removed from your pool each time you backwash.