opening pool - water test results

[mike_311]

1. i have the K-2006.

2. about 190ppm

3. what does this do, beside chlorinate my pool...?

4. that bad huh? about $100 to refill.

==============================
also which kit? the k1515a or c one is $15, one is $50...

[PoolDoc]

OK. 190 ppm CYA.

What that means is that you'll either have to drain the pool OR you will have to run a NORMAL level of chlorine 15 - 20 ppm.

Downsides:
- the ONLY way to test your chlorine is with the K-2006 (C model has 3x the test reagents -- get it, if you don't drain!)
- you'll need a $75 pH meter to test your pH (high chlorine screws up the pH test, though maybe not with CYA=200ppm.)
- dealing with algae will be a little tricky, and you'll need to keep a $20 bottle of sodium bromide on hand for that purpose
- if you have your water tested by a dealer, you'll get weird responses, ranging from head scratching (Not sure what's going on with your water) to panic and hyped up sales attempts (OMG! Drain today or die! And, buy $1,000 of our chemicals to help clean up!)

Upside:
+ chlorine usage will be VERY low.
+ you'll be able to dose chlorine 1x per week (go from 15 ppm to 20 ppm)
+ vacations will be easy (just dose to 25 - 30 ppm -- and take off. As long as the pump runs, and you're back within 10 days, you should be fine!)
+ your water chemistry will be VERY stable.
+ If you also use borax at 50+ ppm, you will have even MORE stable water chemistry, reduced chance of algae, and very high water quality

Your choice, though. If you drain, drain to 1/4 level, so you don't have to add stabilizer

The Best Guess page, linked in my sig, explains some of the chemistry and the options.

[mike_311]

trying to figure out how low to drain. what level of CYA am i shooting for?

[PoolDoc]

Well, based on your results, you should have a final level of about 50 ppm, if you drain your pool to the 3/4 empty point, and then refill. 50 ppm is a good level to use with bleach, if you want to operate conventionally.

[mike_311]

i dont want to take it down too far because if the vinyl liner. there was about 3' of water in it if i take it down to a foot and refill full with with the 4' or so of water that should put me at about 50ppm.

its about 18" deep now so a few more hours and i'll start the refill.

what this first step after that?

set the ph? what value?

add chlorine? how much?

[Watermom]

With a CYA of around 50, you want to keep the chlorine level between 3-6 all the time. If you dip below that, you risk an algae bloom. In this size pool, each quart of 6% bleach will add 2ppm of chlorine. Use that as a reference to help you determine how much bleach to add. Each evening, you'll want to test pH and chlorine. At that time, add enough chlorine to get the level back to 6ppm.

While you are refilling it, go ahead and add a little bleach. Every foot of water added, add a quart of bleach. By the time you have it filled up, that should be about a 3 quart jug having been added which should take you to about 6ppm.

With a CYA of 50, you won't want to use any forms of stabilized chlorine, meaning no trichlor pucks nor dichlor shock powder or else your CYA will continue to rise.

Although not critical, you may want to lower your alk a little to get it between 80-120 or so. Read about this process here: Lowering Alkalinity Step-by-Step


Also, read the "using muriatic acid safely" link in my signature below.

[mike_311]

btw, thanks you so much for this forum. i really appreciate all the advice.

my wife picked up a few bottles of Clorox (6%) is that ok or do i want something else? i realize that it not be the most cost effective brand, but that's what she got when i said plain 6% bleach

so are there any chlorine tabs i can use or am i keeping the pool chlorinated with bleach only?