Re: new salt chlorinator system
Quote:
Originally Posted by
JimK
I would appreciate your input on my routine and if you have any suggestions that may save me time and money.
Jim, I had to go look up some of your IP addresses, to find out approximately where you are. Virginia is much more like Tennessee or N. Georgia, then like California . . . and I'm pretty sure we have more of a problem with algae than folks in S. California or Arizona.
Richard (Chem_Geek), Mark (mas985) and I have gotten an email discussion going about this that's probably up to 3,000 words in just a few hours. I guess we'll need to migrate it to the China Shop.
In your case, if I were you, I'd experiment with dropping the polyquat rather than the borates. Unless you are backwashing a LOT, you shouldn't be having to add borates much. One caution: polyquat is a pretty effective clarifier, so if that function is affecting your pool and you lose clarity you might try substituting a small dose of a conventional clarifier.
You might want to raise the borate level a bit. I still have no hard data, but it seems that 50 ppm may be the low end of the range for effective algae-stasis.
Best wishes!
Re: new salt chlorinator system
Ben, the 5% CAME from Chem geek! It has been proven to be effective in a vast majority of salt pools, possibly because of the super shocking that occurs in the cell. (In fact I am not familiar with one case where there were algae problems with someone following it and making sure that FC did not drop below that but,as we know, there are always exceptions to everything!) Also, remember that 5% is the MINIMUM FC level you should run.
Re: new salt chlorinator system
Quote:
Originally Posted by
JimK
After a steep learning curve, I settled on a routine that has worked for me for the past several seasons. It pretty much includes the following:
FC at 5 (as mentioned, controlled using an Aquarite SWCG)
TA 80-100 (I use bicarb to raise when it gets low)
If you drop the TA down to 70 or even 60 you will have a slower pH rise since there will be less outgassing of CO2, the primary cause of pH rise in most pools (excluding curing plaster).
PH 7.5-7.8 (I add muriatic acid once it hits 7.8; PH has never been too low, so I've never had to add anything to raise it)
Wait for the pH to climb above 7.8. If you are testing it regularly you will see when this happens before it goes too high. Borate tends to stabilize the pH at 7.7 to 7.8 for an extended period of time compared to pools without borate.
Borates 40-50
CYA 70-80
In terms of regular maintenance, besides testing and adjusting the above as needed, each week I add a maintenance dose (8oz) of Polyquat 60 and a maintenance dose of Jack's Magic Purple Stuff (12oz; I use to have problems with staining before using this. I was told the staining was a side effect of the SWCG. Since using it, I've not had any staining problems.). I shock every 2 weeks (or after a big storm) using calcium hypochlorite (68%). Also, I run the automatic vacuum frequently to keep the pool clean (every couple days on average).
I'm not sure if I'm overdoing things and wasting money by using both Poly60 and borates. I started using them at about the same time (I was fed up with the liner frequently getting slick with aglae so decided to hit it with both guns!) so I'm not sure if just using one would give me the same algae control.
I would appreciate your input on my routine and if you have any suggestions that may save me time and money.
Thanks again.
I would use sodium hypochlorite (liquid chlorine or bleach) instead of the cal hypo. I assume you are not testing your CH because it is a vinyl pool. This is NOT a good idea with a SWCG since scaling of the cell is a real worry. Just because you don't NEED calcium added if it is low does not mean you do not need to know what the level is so you can avoid possibly scaling conditions.
Re: new salt chlorinator system
Quote:
Originally Posted by
waterbear
Just because you don't NEED calcium added if it is low does not mean you do not need to know what the level is so you can avoid possibly scaling conditions.
Good reminder!
Re: new salt chlorinator system
Quote:
Originally Posted by
PoolDoc
Jim, I had to go look up some of your IP addresses, to find out approximately where you are. Virginia is much more like Tennessee or N. Georgia, then like California . . . and I'm pretty sure we have more of a problem with algae than folks in S. California or Arizona.
Yes, I'm on the coast, lots of water around here and lots of humidity during the summer!
Quote:
In your case, if I were you, I'd experiment with dropping the polyquat rather than the borates. Unless you are backwashing a LOT, you shouldn't be having to add borates much. One caution: polyquat is a pretty effective clarifier, so if that function is affecting your pool and you lose clarity you might try substituting a small dose of a conventional clarifier.
Once up and running, I usually only have to backwash my DE filter once or twice the entire season (May-October). The water has always stayed crystal clear, even before I started using the polyquat, so perhaps losing clarity may not be an issue? It's not very often I have to add borates. I may try stopping the polyquat applications and see what happens. That said, I've already purchased enough polyquat to last the entire season, so I may just continue with it this season and try doing without next season (unless curiosity gets the best of me and I don't want to wait that long...LOL).
Quote:
You might want to raise the borate level a bit. I still have no hard data, but it seems that 50 ppm may be the low end of the range for effective algae-stasis.
Best wishes!
Can you recommend a more effective range? BTW, if it makes a difference, the borate I'm using is BioGuard's "Optimizer" (I'm sure it cost more per pound, but a 20lb bucket lasts me a long time, so my cost per season is low). The label on the bucket recommends keeping the level at least 35, I shoot for 50 because this was recommended by someone I trust. If you need it, I can check the container tomorrow and see what the chemical name is for "Optimizer" (it's a big long name that I don't remember).
Quote:
Originally Posted by
waterbear
I would use sodium hypochlorite (liquid chlorine or bleach) instead of the cal hypo. I assume you are not testing your CH because it is a vinyl pool. This is NOT a good idea with a SWCG since scaling of the cell is a real worry. Just because you don't NEED calcium added if it is low does not mean you do not need to know what the level is so you can avoid possibly scaling conditions.
Thanks for the tips on TA levels and PH.
Actually, I do have CH checked a couple times a year. I just checked my records going a couple years back and the level seems to always be in the 200-250 range. I've never experienced scaling on the salt cell. Perhaps we get enough rain here in SE VA to keep CH levels in check? Speaking of CH levels, the paperwork that came with my pool states that CH is necessary to keep the liner from becoming brittle. Is this true or BS?
After reading the posts and recommendations in this forum, I've considered using plain bleach, but with all the uncertainties about it's actual strength (how long has that jug been sitting on the shelf or in a warehouse?), keeping a bunch of jugs on hand or making frequent trips to the store (I don't like shopping), using cal hypo just seems much more convenient to use (I just have to buy it once at the beginning of the season). Since my CH level seems to stay in check, do you think it's OK to keep using cal hypo?
PS - I forgot to mention when describing my routine that I try to always test my water at about the same time in the evening (about 6pm). I figure this would give me a FC reading at its lowest point during the day. I take the sample from the deep end about 18" below the surface and away from any returns.
Re: new salt chlorinator system
Quote:
Originally Posted by
waterbear
Ben, the 5% CAME from Chem geek! It has been proven to be effective in a vast majority of salt pools, possibly because of the super shocking that occurs in the cell. (In fact I am not familiar with one case where there were algae problems with someone following it and making sure that FC did not drop below that but,as we know, there are always exceptions to everything!) Also, remember that 5% is the MINIMUM FC level you should run.
Interesting that this pool calculator, www.poolcalculator.com/ , recommends the same thing. If I type in a CYA level of 80, for SWCGs it recommends a minimum FC level of 4 (ie 5%).
Here's a snippet from that site;
Quote:
...Many people find that a SWG will work with a slightly lower FC level than other forms of chlorine....
Re: new salt chlorinator system
The pool calculator was originally written by "JasonLion" over at TFP and it was at TFP where chem geek (Richard) basically came up with the 5% and we tested it out and it worked very well (back when I was a Mod over there) so it's no surprise that Jason incorporated Richard's guidelines into his pool calculator. We did a lot of experimentation and 'tweaking' in the early days of TFP. The pool calculator has since been sold to pSIFlow Technology Inc. and I am not sure if it is being updated anymore.
The active ingredient in the original Optimizer is/was sodium tetraborate pentahydrate (borax). It requred the addition of acid along with it to maintain the pH. If you have the pH neutral product that does not require acid addition to maintain pH then it is mostly boric acid with some borax (about 90% boric acid and 10% borax, pentahydrate form, by weight). 50 ppm is considered optimum for borate in a halogen (chlorine or bromine) pool, 30 ppm is the lowest effective level for algaestatic effect. 50 to 80 ppm is recommended for biguanide pools but there is a very small concern of possible toxicity at the higher levels. These levels go back to the original tests done by John Girvan of Proteam in his test pools in St. Augustine and Jacksonville, Florida in the early '80s before he sold his company to Haviland and went to work for them.
Re: new salt chlorinator system
Quote:
Originally Posted by
JimK
Speaking of CH levels, the paperwork that came with my pool states that CH is necessary to keep the liner from becoming brittle. Is this true or BS?
I've several times talked to engineers at the companies that make the vinyl sheeting (not completed liners) and they tell me it is NOT true. In any case, if you did have loss of calcium chloride, it wouldn't make the vinyl brittle. PVC is naturally brittle, with or without calcium carbonate filler -- you have to add a plasticizer to make it flexible. Loss of plasticizer WILL make it brittle.
Quote:
Originally Posted by
JimK
Interesting that this pool calculator,
www.poolcalculator.com/ , recommends the same thing. If I type in a CYA level of 80, for SWCGs it recommends a minimum FC level of 4 (ie 5%).
As Waterbear notes, it's not exactly a coincidence.
Quote:
Originally Posted by
waterbear
50 to 80 ppm is recommended for biguanide pools but there is a very small concern of possible toxicity at the higher levels.
As best I can tell, the toxicity issue applies primarily to folks who have (a) male dogs who (b) drink a lot of pool water, and (c) have not been fixed, but are planned (d) for breeding. Significant borate ingestion can impair canine fertility and is possibly mutagenic. One of the other PF Support Team members does not use borates because she breeds German Shepherds and they do drink a lot of pool water.
Re: new salt chlorinator system
Quote:
Originally Posted by
waterbear
The pool calculator was originally written by "JasonLion" over at TFP and it was at TFP where chem geek (Richard) basically came up with the 5% and we tested it out and it worked very well (back when I was a Mod over there) so it's no surprise that Jason incorporated Richard's guidelines into his pool calculator. We did a lot of experimentation and 'tweaking' in the early days of TFP. The pool calculator has since been sold to pSIFlow Technology Inc. and I am not sure if it is being updated anymore.
Thanks for the clarification.
Quote:
The active ingredient in the original Optimizer is/was sodium tetraborate pentahydrate (borax). It requred the addition of acid along with it to maintain the pH.
Yes, this is what I use. I have to add acid as it does cause the PH to shoot up.
Quote:
...50 ppm is considered optimum for borate in a halogen (chlorine or bromine) pool, 30 ppm is the lowest effective level for algaestatic effect. 50 to 80 ppm is recommended for biguanide pools but there is a very small concern of possible toxicity at the higher levels. These levels go back to the original tests done by John Girvan of Proteam in his test pools in St. Augustine and Jacksonville, Florida in the early '80s before he sold his company to Haviland and went to work for them...
So according to this information, my borate level of 50 is fine. Correct?
Quote:
Originally Posted by
PoolDoc
I've several times talked to engineers at the companies that make the vinyl sheeting (not completed liners) and they tell me it is NOT true. In any case, if you did have loss of calcium chloride, it wouldn't make the vinyl brittle. PVC is naturally brittle, with or without calcium carbonate filler -- you have to add a plasticizer to make it flexible. Loss of plasticizer WILL make it brittle.
I see. It has been quite some time since I purposely added calcium to the pool since the CH level always seems to be in the lower to mid 200s (last night I checked my records going back a few seasons to verify this). As was mentioned here, I guess the calcium is coming from the cal hypo I use to shock, and since it hasn't been continually increasing, I'm assuming that we get enough water exchanges via rain throughout the season to keep it in check. Also, I've never experienced any scaling on the SWCG cell.
You said the loss of plasticizer would cause the vinyl to become brittle. What causes a loss of plasticizer?
Quote:
As best I can tell, the toxicity issue applies primarily to folks who have (a) male dogs who (b) drink a lot of pool water, and (c) have not been fixed, but are planned (d) for breeding. Significant borate ingestion can impair canine fertility and is possibly mutagenic. One of the other PF Support Team members does not use borates because she breeds German Shepherds and they do drink a lot of pool water.
That's not an issue here as we don't have any dogs. Besides, if we did have any, they would be fixed (I use to work at an animal shelter know all too well the consequences of too many dogs and cats and not enough good homes; it's absolutely heartbreaking......).
You mentioned you thought a borate level of 50 might not be enough. Could you elaborate and suggest a level that may be more appropriate for me?
Thanks everyone. I'm learning alot here and appreciate the feedback.
I do feel bad for hijacking this thread, so I'll at least try to share with the OP some of my experience with using a SWCG.
First of all, although this is the only pool I've ever owned and it has always had a SWCG so I cannot compare 1st hand to a traditionally chlorinated pool, my guess is that despite what manufacturers say there is really no cost savings in the long run (the units aren't cheap and replacement cells are expensive). I think in the end overall costs are similar.
Also, even though my SWCG has a "superchlorinate" feature (causes it to run at 100%) for shocking, I no longer use it. With my first/original cell, I did use this feature on a regular basis (per pool stores instructions) and my cell ended up failing within 4 years (it still had a little warranty left on it, so the replacement cost was reduced). I stopped using the superchlorinate feature once I got the new cell. It makes sense to me that the fewer hours I put on the cell, the longer it will last. So now when I want to shock, I turn the cell off and just use the traditional method (cal hypo in my case). Next month it will have been 4 years since I got the replacement cell and so far it's still working fine. Hopefully this means I will get more seasons out of this cell than the last one. Bottom line, I only use the SWCG to maintain FC levels.
The first few years of owning my pool, I had an issue with metal staining (each successive season it got worse and more frequent). At first it was just on the steps and I had to clean them a couple times a season with ascorbic acid (not a big deal). As time/seasons went by, the steps would stain more frequently and eventually the entire liner started showing staining (a big dose of ascorbic acid was required to get rid of all the stains: the process was a pain but it worked). The manager of the place who installed our pool said that this was a side effect of the SWCG; that the small amount of impurities (iron?) in the pool salt were building up and causing the staining. At that time after a bit a research I started using Jack's Magic Purple Stuff and have not experienced any staining since (a tip: ordering it online is much cheaper than buying it in the store, although it still cost me about $200 per season [May-October here]). Supposedly, it's also suppose to help protect the cell and help it last longer. I would like to hear from our experts here about this issue with SWCGs (if it really is the cause).
In another thread in which I was asking if CYA was necessary, I referenced an article I found that included that person's experience using a SWCG. He complained that the cell failed within a year and the manufacturer wouldn't honor the warranty. I found this puzzling since I've also experienced a couple problems while under warranty and had no trouble with the same manufacturer honoring it. It made me wonder if the reason his warranty claim was denied is because he didn't maintain the pool according to the manufacturer's instructions (he wasn't using any CYA). He also complained that the salt was corroding his stainless ladder. I also found this puzzling since I've never experienced this issue (our pool was installed in 2004 and has always used a SWCG since day one). I guess just make sure you don't keep too much salt in the pool (follow the manufacturer's guidelines).
For me, there are three primary advantages to having a SWCG;
1. Convenience. Maintaining constant FC levels is easy once you get everything balanced and going. I don't have to mess with handling and storing chlorine (except for the cal hypo I use to shock with).
2. The water feels better and is much less irritating to my skin and eyes (friends have also mentioned this about our pool). That said, perhaps you could get the same benefit in a traditionally chlorinated pool by adding salt to it (what do our experts here think?)?
3. We can go on vacation without worrying about maintaining FC levels.
I hope something in here helps the OP.
Re: new salt chlorinator system
A few thoughts:
50 ppm borate is fine in my opinion.
A cheaper source of borax is 20 mule team borax from the grocery. It's the same stuff except that it is the decahydraate form (it has 10 water molecules attached instead of 5) so you need a bit more by weight for the same borate level (60 oz by weight will raise 1000 gallons 50 ppm and needs abut 30 fluid oz of muriatic acid to keep the pH in line. The pentahydrate form requires about 45 oz by weight and the amount of acid to achieve 50 ppm rise in borate in 1000 gallons while using boric acid requres about 38 oz by wieght and will very slightly lower the pH but this is not a concern since it will rise on it's own as CO2 outgasses.)
If you want a pH neutral borate souce that is available commercially then Proteam Supreme Plus is the product you want. Proteam Supreme is exactly the same at Bioguard Optimzer (sodium tetraborate pentahydrate). The Supreme Plus is a mix of boric and and the pentahydrate form of borax to make it pH neutral. However, all the commercial forms of borax are MUCH more expensive than 20 mule team borax from the grocery store.
The main reason to use sodium hypochlorite (particularly since you have a vinyl liner) is that calcium hypochlorite is slow dissolving and can bleach the liner if it falls on it undissolved. Also, Sodium hypochlorite is what the salt cell is is actually making. As far as worrying about the 'freshness of the bleach" it's really a moot point. Unless you are buying it at a discount store or dollar store it's probably fresh. Walmart has a big turnover so it's a good place to buy it. If they sell pool chlorine in refillable carboys in your area that is often the best deal. Just buy enough for shocking and don't stockpile it so it does not stick around for more than a month or two before getting refilled. One gallon of 12.5% pool chlorine will raise you pool about 6 ppm, btw, so a 2 1/2 gallon carboy should be just about right for shocking your 22000 gal pool (or 5 gallons of 6% laundry bleach). If you use cal hypo predissolve it first. You do not want undissolved cal hypo going through the salt cell or falling on your liner.
As far as your metal problem, Were the stains brown (iron)? Do you fill with well water? What kind of salt do you use? I have seen some fine crystal "pool salts" that have caused iron staining which is why I recommend using solar water softener salt (The larger crystals do not need anti caking agents). I suspect that anti caking agents are sometimes added to the fine crystal pool salt or they are using food salt (which also contains anti caking agents) and repackaging it. Yellow prussiate of soda (sodium ferrocynaide, an iron salt) is used as an anti caking agent in food salt.
