+ Reply to Thread
Page 5 of 5 FirstFirst ... 3 4 5
Results 41 to 45 of 45

Thread: Ordered My Pool

  1. #41
    Watermom's Avatar
    Watermom is offline SuperMod Emeritus Quark Inspector Watermom 4 stars Watermom 4 stars Watermom 4 stars Watermom 4 stars Watermom 4 stars Watermom 4 stars
    Join Date
    Dec 1969
    Location
    Charleston, WV
    Posts
    9,345

    Default Re: Ordered My Pool

    You'll be ok to go ahead and add some more cya now.

  2. #42
    Join Date
    Jun 2010
    Posts
    27

    Default Re: Ordered My Pool

    Added another pound of CYA this morning. Like I said, that should get me up to around 23 or so.

    Since the Taylor kit's lowest reading is 30, is there a way to alter the test to know where I am right now? More drops/fewer drops, less test water/more test water?

    How do I know that I'm getting close to 30?

    Tested FC this morning, and it was still a solid 3 ppm. No FC loss overnight. Water is sparkling, and things are going well so far. (Knock on Wood)

  3. #43
    Poconos is offline SuperMod Emeritus Whizbang Spinner Poconos 4 stars Poconos 4 stars Poconos 4 stars Poconos 4 stars Poconos 4 stars Poconos 4 stars
    Join Date
    Dec 1969
    Location
    Honesdale PA
    Posts
    1,812

    Default Re: Ordered My Pool

    I don't know about altering the 1:1 ratio but you should be able to judge by how cloudy the sample is getting. The dot doesn't just disappear....it fades away into a blur then to nothing so that should give some idea if you are approaching being on-scale.
    Al
    16'x32' oval 22K gal IG vinyl pool; ; Hayward S244T sand filter; Hayward superpump 1 HP pump; hrs; K-2006; PF:5.5

  4. #44
    Watermom's Avatar
    Watermom is offline SuperMod Emeritus Quark Inspector Watermom 4 stars Watermom 4 stars Watermom 4 stars Watermom 4 stars Watermom 4 stars Watermom 4 stars
    Join Date
    Dec 1969
    Location
    Charleston, WV
    Posts
    9,345

  5. #45
    Join Date
    Jun 2010
    Posts
    27

    Default Re: Ordered My Pool

    Just wanted to give a quick update.

    Pool water is still sparkling. I'm down to adding about 2.5 quarts of bleach a day. It usually ends the day at about 1.2 to 1.6, and we've been bumping it up to 4.0 ppm. CYA should be nearing 30. I've used 2 trichlor pucks this week to pump it up a bit more. I'll probably test it at the end of this week, backwash, and then add the remaining amount.

    However, I'm fairly sure that the pool has a small leak. As I mentioned before, the liner slipped when we were filling, so the sand underneath became quite wet.

    Each morning, there is a wet spot around a section of the pool. At first, we had hoped it was just the weight of the pool pushing the water out of the sand underneath, but it's continued for a couple weeks now. I'm not losing much water, because after considering evaporation, there can't be much water. I guess I need to do the bucket test to compare evaporation for a couple days to know for sure. Not sure how we would've gotten a hole in the liner, but I guess it's possible.

    Beyond that, we've been enjoying the pool, and it's staying nice and clean and clear. I did manage to swim enough to get swimmer's ear, so that's fun. I'm out of swimming commission for a few days, but I'll be back at it soon enough.

    Thanks for all your help folks.

+ Reply to Thread

Similar Threads

  1. Just ordered new AGP. Startup suggestions?
    By Bluemackie in forum Testing and Adjusting Pool Water Chemistry
    Replies: 3
    Last Post: 06-21-2012, 12:33 PM
  2. Pool is ordered!
    By swimlane in forum Above-Ground Pool Construction & Repair
    Replies: 4
    Last Post: 05-31-2011, 10:05 PM
  3. AutoPilot Question (just ordered)
    By jmcst25 in forum Salt Generators (SWCG) & other Chlorine Feeders
    Replies: 3
    Last Post: 05-29-2007, 01:26 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts