Brown water in pool- from Iron

[newguyjosh]

So HTH told me I had to wait until the the free chlorine level was below 1 to add the metal control...is this correct?

My chlorine is measuring around 10 ppm from the intiall shock dose I added I guess...I do not have any stabilizer in there...how long should this take to return to a low enough level?

Also waht level of chlorine is safe to swim in?

Thanks

[newguyjosh]

actually as I look at it more closely it appears the iron/rust has actually collected on the bottom of the pool and walls making the water appear orange...if i brush the bottom of the pool the water below it looks fairly clear..so is there a wait to get this out...the vac that came with the pool sucks and not in a good way

[aylad]

The only way I know to get it out is to vacuum it out, which I would do if you've managed to get it to fall out in solid form. Without stabilizer in the water, by tomorrow afternoon your chlorine should be just about gone. Safe level for chlorine depends on your stabilizer level, but since you have none I'd say safe to swim at 3-5 ppm.

Welcome to the forum!!

Janet

[newguyjosh]

How long do I have to wait to swim after adding the metal control? How quickly should I see results?

[mbar]

You can swim anytime after using metal control. Just check the ph, some sequestering agents lower the ph and use up chlorine, so make sure both are in balance. You want your ph at the lower end no higher than 7.4 for the metal control to lift the recent stains off. High ph along with shock levels of chlorine will let any metals that are not sequestered to fall out of solution.

[newguyjosh]

So how long should I wait from the time I put the metal control in to put a ph minus in? The Ph is about 8.2 now. Whats the highest ph safe to swim?

HTH I was told to let the chlorine get below 1-2 at the highest before putting the metal control in which I did. I put just above the recommended dosage in about 4 hours ago...The water is less brown looking but is more greenish now and definately not clear.

Using test strips I get Free Chlorine at ~1, Ph 8.0-8.4, total alkalinity 240 or more thats as high as it goes, cya at 0...

What do I do next? Is this water safe for myself and girlfriend to get in...had it for a week and would love to get in it. When do I add more cholorine HTH people told me to wait 3 days before adding any more chlorine then another 3 days before shocking..seems like ill end up with algae...

I have had the pump runnning non stop all week

[newguyjosh]

Thanks for the post...I had not recieved any more replies on this thread in awhile and thought maybe people had considered it dead and stopped looking at it..here is a copy of the new day from the other post..Thanks again...

--------------------------------------------------------------------------------
added HTH Ph minus because the Ph was testing at 8.4 or above on my strips.

On saturday morning the water no longer looked brown but now looked green and I could see to the bottom of the pool. I continued to clean the cartridge filter 2-3 times per day and it was always orange and rusty looking. When I scooped water out in a bottle for a sample it looked clear!?

I took a sample of the water in to the pool place and got the following numbers:
Free Chlorine:0
Cya: 0
Total hardenss: 279
Ph: 7.5
Total alkalinity: 369
iron 1.5 ppm
Salt 1700

The pool place told me the iron may continue to decrease over the next few days with the metal control only being added the day before. They also advised me to wait a while longer on adding any chlorine. They said the biggest thing I needed to do was lower the alkalinity and they advised using muratic acid. 1/4 gallon then 1/4 gallon 4 hours later. If still high add more the next day up to another 1/2 gallon. Based on my readings on here I realized i would need to aerate to keep the Ph from dropping too much. My return valve from the filter/pump is angled slightly upward and the total water level for the pool is slightly low so water is splashing quite a bit which I think is doing the job of aeration?

Well at this point I have added 3/4 gallons of muratic acid and the pool still loooks greenish but mostly clear (meaning I can see the bottom of the pool). When I test using test strips the Ph still looks to be around 7.2 and the alkalinity looks just slightly darker then the max on my test strips of 240. I have still not added any more chlorine and I hae not started running the salt water system to generate any chlorine. I plan to take another sample to the pool place tomorrow.

So what should I do now? Keep addint muratic acid? When should I put some liquid chlorine or start the salt system? I'm afraid I'm gonna end up with algae soon (it has been cloudy and raining here the last several days so hopefully that keeps the algage at bay. I have been running the filter pump 24/7 except for cleanings.

Is the green water safe to swim in? I feel like this is never going to clear up. Why is the water in the bottle clear but the pool definately not?

Please help...