waiting for aquarite...

[Poolsean]

TDS of 1000 ppm is not too bad. Total TDS - Salinity = Potentially harmful TDS.
It's a good idea to test your source water, especially for TDS as this should be considered your NORMAL TDS, which should fall between 300 - 700 ppm. These are mostly calciums, magnesiums and metals. When these levels increase to 1000 ppm HIGHER than your normal TDS, then you should consider draining. However, when you have high TDS as a result of the harmful ingredients, your water will also appear dull and cloudy, with a metallic taste to the water, AND your chlorine will be less effective.

High TDS as a result of salt is not harmful.

It is possible for the salinity to be 3500 + ppm from your softwater system. However, that level will be too high for the AquaRite, so in this case, Leslie's is correct in recommending that you drain (not you do not need to do a full drain, just a partial drain will do). Then refill with the water not from your water softener system. You'll just be adding back in the salt.

On a Taylor test kit, it's difficult to distinguish 0 ppm from 23 ppm, but assume that your stabilizer is too low and will need to be added. You want to get to about 60 ppm to 80 ppm. The normal dosage is 1 lb / 5,000 gallons increases 25 ppm.

Alkalinity is high and so is pH so adding acid and aerating should do a good job a lowering both.

Calcium is good, thank God for Water softeners.

Definately treat for Phosphates. The water will get cloudy for a few days as a result, but it is to be expected with phosphates in the pool. Clean out/backwash the filter after the phosphate treatment (when the water gets clear).

The dust storms should not cause an increase in TDS unless you're located close to a golf course that is constantly fertilizing...but that should affect the phosphates more than the TDS.

[BND]

Ok, then...
Plan:
Check source levels( non softened and softened)
Do a partial drain, refill from non softened source, i am thinking 1/2 to be safe.
Check all levels
Treat for phosphates( these should be ZERO correct?)
Backwash
Add salt as needed
Add Stabilizer

[BND]

Switching issue aside for now.
Pool has been drained and refilled (about 80 %)
TDS 1900
Salinity 1400
CYA 0
TA 150-190
Calcium hardness 220
ph 7.6-7.7
phosphates 200
what should be my first step?
Pool is 13,050 gallons

[Poolsean]

For an outdoor pool, increase cyanuric acid to 60 - 80 ppm, which would be about 8 lbs for your pool, to get to about 75 ppm.
Alkalinity is a bit high, but not bad. Direct your return jets up towards the top of the water to aerate. Lower the pH to about 7.2 to 7.4 in conjunction with aeration and the Alkalinity will lower within a few days.
New pools usually require constant testing and adjusting of the pH so keep an eye on this.

Add salt to get to the Aquarite recommended level. To get to 3000 ppm, you will need about 160 - 170 lbs of salt. I'd recommend adding about 150 lbs, let it circulate for a few hours, then see what the unit displays as your salt level. Let it run overnight and retest the following day and add more salt if needed.

Sit back, and enjoy your pool!

Thanks for selecting a salt system for your pool.

[BND]

Going to try to finsih this up in the next day or two.
I didnt see anything in the manual about a speciffic length of the pipe i should cut out to maintain the best fit ( for the turbo cell).
My thought was to connect the unions to the cell then hold the cell along the pipe i intend to cut and try to mark on the pipe the spots i need to cut.
But if some one could say.."cut out exactly 14.5 inches ", that would help...