Pump Size

[poolpup]

I will be having an 18x43x28 40,000 gal true L shaped pool installed soon and was wondering if a 1 1/2 hp pump will be adequate enough for the size.

[aylad]

Bumping this post so it'll get some attention--it's been in the "practice" forum. Just moved it here so poolpup will get some useful answers...

Janet

[thepoolman1]

Unless you will have 2.5" plumbing or larger, a 1.5hp pump will be too large for your system. You will also need a filter that can handle the flow of a pump that large. If you are going to use a 2-speed pump (highly recommended), the occasional use of the high speed of a 1.5hp would probably not cause many problems, even on 2" plumbing.

I have successfully filtered older pools in the 40 - 50k gallon range that had very undersize (for today's standards) plumbing, hand-formed skimmers and usually only 1 return line and inlet with 1/2 and 3/4hp pumps. Bigger is seldom better in pool pump sizing.

[stualden]

Poolman1, is a 1.5 horse dual-speed likely to be a good candidate for a 32,000 gal. in-ground pool too?

I have two motors, both of which are on their deathbeds. One is a 1 horse, one is a 2 horse (but with an impeller that says 1.5 horse). Pumps are old UltraFlow, installed by Sylvan in 1991. All plumbing is 1.5", except (curiously) for the final return to the spa, which is 2". The pool filtration circuit passes through a Titan stainless steel 60 sf filter and a new Sta-Rite heater.

I had always assumed that the 2 horse was for the pool, but your note suggests that it's for the spa jets. Does that sound right? Everything was unassembled when I bought the house and I didn't know any better.

Is the two-speed a good choice for the pool, with a manual switch just to get high speed when backwashing or doing other maintenance chores? Thanks.

[duraleigh]

Poolpup,

Poolman's advice is on the money. I have a full-rated 1.5HP pump for a 43,000 gal. pool (2" plumbing) and I would've been a little more efficient with a full rated 1HP. My only saving grace is I have a very large sand filter (950 lbs) so my system is ok.....just could've saved some money with less pump and had a little better system.

(Full-rated pumps are about .5HP stonger than up-rated pumps)

Stu,

based on your preliminary info, 1.5 sounds a little large for the pool....unless your going to drive both pool and spa from one pump.....then maybe a 2hp 2-speed would be a good mix. Others more experienced with spas than me will chime in soon and give you a better-educated answer.

[stualden]

Thanks Dave. I'll always use a separate pump for the spa jets, so the existing 2 horse (or a direct replacement) should be okay for the spa. I read something relating hp requirements to number of jets - in this case I have 6 (it's a nice roomy spa).

I will get out the pencil and paper and the Ultra Flow charts and figure out what my requirements are for the main filter circuit. I suspect that 1 hp single speed is right (i.e., Sylvan sized it correctly). What I want to figure out is if the Ultra Flow pump can work with the lower RPM of a two-speed motor, and if so, what size motor will give best results for regular filtration at the lower speed.

[myLABSpool]

I want to test my understanding about pump size and line size with some of the "forum experts" and get some feedback from others about this...

I just had an 18x36 IG vinyl liner pool installed and the pump and line size is different from what the sales person said...

What got installed is:
-- 1 hp sta-rite pump
-- 1.5" plumbing
-- 300 lb sta-rite sand filter
-- sta-rite heater
-- the filter/pump is about 35 feet from the water
-- 3 return lines (one deep for better heating)
-- 1 skimmer
-- 2 main drains

The sales person said we would get 2" plumbing & 1.5 hp pump (the contract says 1.5hp pump, but does not specify plumbing size). The guys that did the work said they always use 1.5" plumbing.

The question for the forum is, should I complain to them and if so, how much of a big deal should I make of it? They may offer to swap out the 1.0 hp pump for 1.5 hp, but I don't know if I would want that.

From what I've read in this forum it seems like what was installed is good and that going with a pump that is too big can waste electricity and force too much water through the filter making it less efficient. It just bugs me that what was installed is different from what the sales guy said. The company is a very reputable company and has been installing pools for 35 years.

Opinions please.

Thanks

[waterbear]

I want to test my understanding about pump size and line size with some of the "forum experts" and get some feedback from others about this...

I just had an 18x36 IG vinyl liner pool installed and the pump and line size is different from what the sales person said...

What got installed is:
-- 1 hp sta-rite pump

The sales person said we would get 2" plumbing & 1.5 hp pump (the contract says 1.5hp pump, but does not specify plumbing size). The guys that did the work said they always use 1.5" plumbing.

The question for the forum is, should I complain to them and if so, how much of a big deal should I make of it? They may offer to swap out the 1.0 hp pump for 1.5 hp, but I don't know if I would want that.

Opinions please.

Thanks

There is a numbers game that manufactuers play with pumps. It is called the service factor. Without going into too much detail it means that there are 'full rated" pumps and 'up rated' pumps. What that means is a 1.5 HP uprated pump is EXACTLY THE SAME PUMP as the 1 HP full rated one in the same model line. (same impeller, volute,housing, etc...You can check the parts numbers on replacement parts to verify this). They only difference is the faceplate on the motor (even though the motors are the same). An example would be a full rated 1 HP motor with a service factor of 1.65. This gives a brake HP of 1.65 (rated HP x service factor). The uprated 1.5 HP model will have a rated HP of 1.5 with a service factor of 1.1 for a brake HP of 1.65! (rated HP 1.5 x service factor 1.1= brake HP 1.65!) Sta-rite has both full rated and up rated pumps. If the contract called for a 1.5 HP uprated pump and they put in a 1 HP full rated pump from the same model line you did get what the contract called for. Believe it or not, even though the full rated pump one size down from the uprated model is the same pump with identical parts the two pumps will have different costs so a substitution like this is not really a bad thing.
If they substitued a smaller full rated for a larger full rated or a smaller up rated for a larger up rated then you did not get what the contract specified.
Hope this helps.