+ Reply to Thread
Results 1 to 10 of 11

Thread: muriatic acid

Hybrid View

  1. #1
    Join Date
    Dec 1969
    Location
    ohio.
    Posts
    20

    Default muriatic acid

    I am still trying to get my alkalinity down. I have an above ground pool (about 5500 gallons) 18X48. My alkalinity readings are still around 280. I have just been adding 1 cup and sometimes 1 1/2 cups of acid but my ph is only dropping down to 7.2 to 7.5. Can I add 2 cups at a time or that too much? I don't won't to ruin my liner.

  2. #2
    Join Date
    May 2006
    Location
    Downingtown, PA
    Posts
    192

    Default Re: muriatic acid

    Wolf,
    I don't think the muriatic acid is going to bring that TA down. I believe you need to either do a partial drain and re-fill or read up on aerating the pool to lower alk.
    Outside of Philadelphia, PA
    18' x 40' IG - 22K gallons
    Sylvan Gunite Pool (1979)
    Plaster re-done (1997)
    48 Sq Ft Hayward D.E. Filter (2003)
    1.5 hp Hayward Super Pump (2006)

  3. #3
    CarlD's Avatar
    CarlD is offline SuperMod Emeritus Vortex Adjuster CarlD 4 stars CarlD 4 stars CarlD 4 stars CarlD 4 stars CarlD 4 stars CarlD 4 stars
    Join Date
    Dec 1969
    Location
    North Central NJ
    Posts
    6,607

    Default Re: muriatic acid

    Quote Originally Posted by Bleach=Chlorine?
    Wolf,
    I don't think the muriatic acid is going to bring that TA down. I believe you need to either do a partial drain and re-fill or read up on aerating the pool to lower alk.
    This is not correct. Go to the top of this forum and read the stickie'd posts for how to lower T/A.

    Lower pH to 7.0 to 7.2 (T/A will come down some), then aerate to raise pH w/o raising T/A. Then lower pH to 7.0 to 7.2 again and aerate again.

    T/A will rachet down until you hit your target.

    T/A moves up and down with pH. But by aerating you can raise pH WITHOUT raising T/A.
    Carl

  4. #4
    Kimrst is offline Registered+ Thread Analyst Kimrst 0
    Join Date
    Dec 1969
    Location
    Michigan
    Posts
    53

    Default Re: muriatic acid

    I have about the same problem as the wolf. I am aerating my pool with the sprayer that I bought with the frame set. I read docs notes and it said it can take awhile "You must be patient; you can not hurry the process;" How long should I be running the fountain? The water here in sw Michigan is very cold yet. (72* near the solar cover) Could this be part of it? OR could the vinal of the intex pool have anything to do with it? Maybe not enough stablizer? I know run my numbers and post them.. ..What I'd really like to do is take a sample to a pool place, but out here in tim-buck-too its a drive to get to a pool place...It will probly be July before it gets warm enough to swim in anway.. :-( Kimrst

  5. #5
    Join Date
    Jun 2006
    Location
    Sun Prairie, WI
    Age
    56
    Posts
    74

    Default Re: muriatic acid

    Quote Originally Posted by Kimrst
    {snip}
    The water here in sw Michigan is very cold yet. (72* near the solar cover)

    ...It will probly be July before it gets warm enough to swim in anway.. :-( Kimrst
    {snip}
    That sounds warm compared to my pool, mine is still 62. Hopefully the parts I need to get my heater back up and running will be in soon.

    Sorry for the OT post.

  6. #6
    Join Date
    May 2006
    Location
    Morris, IL
    Posts
    354

    Default Re: muriatic acid

    I have been trying to get my TA down for around two weeks, and it started at over 230, and as of now, it is around 180, I lowered the PH again to around 7.2, and I have the jet pointing so it blows just out of the water. This raises the PH naturally, and by lowering the PH and the TA together with the Muratic Acid, I am slowly lowering the TA. This is my first year tending to the chemicals in the pool, and I am glad I found this site, so far so good, the water has been perfectly clear and balanced except for the TA, which nobody really notices, so I get the added benefit of looking good.

    Oh, and today, our water was 95, to hot for me though, had to turn the heater down. lol.

  7. #7
    Join Date
    Dec 1969
    Location
    ohio.
    Posts
    20

    Default Re: muriatic acid

    This is all new water. This is an intex pool that you have to take down in the winter. I have been adding a cup a acid to lower ph and then aerating for about 2 weeks now, but my ph was only going to around 7.5 Then we tried 1 and half cups of acid, but the ph is still not going lower than 7.2. Do you think I can add 2 cups of acid and then aerate?

  8. #8
    duraleigh Guest

    Default Re: muriatic acid

    Do you think I can add 2 cups of acid and then aerate?
    Yes, that should do it.

  9. #9
    Join Date
    Dec 1969
    Location
    ohio.
    Posts
    20

    Default Re: muriatic acid

    My water is also cold (72) here in Ohio. Thanks to everyone for the help. I will try 2 cups.

    Peggy

+ Reply to Thread

Similar Threads

  1. Lowering TA with Dry Acid Or Muriatic Acid
    By CelticDaddio in forum Dealing with Alkalinity and Calcium
    Replies: 30
    Last Post: 07-05-2007, 12:54 AM
  2. How much Muriatic Acid?
    By mccato in forum Using Chlorine and Chlorinating Chemicals
    Replies: 6
    Last Post: 08-29-2006, 08:21 AM
  3. How to add muriatic acid
    By BullDean in forum Pool Chemicals & Pool Water Problems
    Replies: 5
    Last Post: 06-12-2006, 10:51 PM
  4. how much muriatic acid
    By wolfcue in forum Dealing with Alkalinity and Calcium
    Replies: 10
    Last Post: 06-07-2006, 05:55 PM
  5. How much muriatic acid to add?
    By Blemished_Chemist in forum Testing and Adjusting Pool Water Chemistry
    Replies: 2
    Last Post: 06-04-2006, 08:15 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts