+ Reply to Thread
Results 1 to 10 of 21

Thread: filter/pump problems - pool newbie

Hybrid View

  1. #1
    Join Date
    Dec 2004
    Location
    Indiana.
    Posts
    700

    Default Re: filter/pump problems - pool newbie

    Quote Originally Posted by ryanm
    That is interesting that you're saying cartridges are not as easy as sand. I definitely got the impressing cartidges were easier from what I've read on various sites. The concept of it seems easier to me for some reason.
    Until you have to clean them, cartridges are easier. With sand, to clean you turn a valve, let the pump run for a couple of minutes while sipping a drink, shut the pump off, turn a valve, let the pump run a minute or so while sipping a drink, shut the pump off, turn a valve, turn the pump on and go swimming. IMO, cartridges are the hardest type of filter to use and sand the easiest.

  2. #2
    Join Date
    May 2006
    Location
    Downingtown, PA
    Posts
    192

    Default Re: filter/pump problems - pool newbie

    Ryan,
    Keep the DE Filter bro! The reason the pressure keeps rising is because that 5 micron filtering ability is getting bogged down with that cloud of dead algea in the water. Just clean the filtering elements the best you can and then fire it up. Make sure your adding the DE through the skimmer and not directly into the DE filter before turning it on. Then wait for the pressure rise and repeat. Spend all day Saturday and by the end of it you should have a clean pool.
    Outside of Philadelphia, PA
    18' x 40' IG - 22K gallons
    Sylvan Gunite Pool (1979)
    Plaster re-done (1997)
    48 Sq Ft Hayward D.E. Filter (2003)
    1.5 hp Hayward Super Pump (2006)

  3. #3
    Join Date
    Jun 2006
    Location
    Pottstown PA
    Posts
    9

    Default Re: filter/pump problems - pool newbie

    So I'm going to need to keep opening up the filter and hosing them off or just backwashing? Let me see if I have backwashing right. My filter has three in/outs. One has the output from the pump going to it, the other outputs to the pool and the third has a valve on it which I can open to drain it. Is just opening up this third valve and draining it "backwashing"? From what I have read it seems there is more to backwashing than just draining.

    The time I opened it up and it was all green, prior to opening it I drained it and the water was all cloudy/green but now if I just let it drain a bit (for like 10 seconds) the water stays pretty clear.

    thanks

  4. #4
    Join Date
    May 2006
    Location
    Downingtown, PA
    Posts
    192

    Default Re: filter/pump problems - pool newbie

    Yes that is your backwash valve and when you get a pressure rise of 5-8 lbs then you want to backwash the filter until the water runs clear. Basically you are reversing the flow and sending all the gunk that is caked on your grids out in the yard. Once the water runs clear shut down the equipment again, set the valve back to filter, start up the equipment again and then add like 75%-80% of the required DE in the skimmer with filter/pump running. Check that the pressure returned to normal and you are all set.
    ** When it is REAL nasty you may have to open it up and actually clean the filter elements but if the pressure drops to normal and does NOT immediately rise back up you should be fine with backwashing.
    Outside of Philadelphia, PA
    18' x 40' IG - 22K gallons
    Sylvan Gunite Pool (1979)
    Plaster re-done (1997)
    48 Sq Ft Hayward D.E. Filter (2003)
    1.5 hp Hayward Super Pump (2006)

  5. #5
    Join Date
    Jun 2006
    Location
    Pottstown PA
    Posts
    9

    Default Re: filter/pump problems - pool newbie

    How do I know what "normal" pressure is? So far in my experience it's either been REALLY low (like non existent) or it's around 20psi. I know the max psi of the filter is 50. If my filter elements were messed up (damaged) how would I know?

    thanks

  6. #6
    Join Date
    May 2006
    Location
    Downingtown, PA
    Posts
    192

    Default Re: filter/pump problems - pool newbie

    If you had damaged filter fingers stuff would be coming out the returns back into the pool. If that is happening you have a problem with the filter. I think some people here run a pressure around 20psi, my norm is 11psi not that it matters. Without running the pool with a clean filter and clean pool it might be tough to know what the "normal" pressure should be. Is there THAT much junk in the water? Hang in there and keep the Chlorine level up in shock territory.

    Pottstown huh? We're practically neighbors!
    Last edited by Bleach=Chlorine?; 06-15-2006 at 04:25 PM.
    Outside of Philadelphia, PA
    18' x 40' IG - 22K gallons
    Sylvan Gunite Pool (1979)
    Plaster re-done (1997)
    48 Sq Ft Hayward D.E. Filter (2003)
    1.5 hp Hayward Super Pump (2006)

  7. #7
    Join Date
    Jun 2006
    Location
    Pottstown PA
    Posts
    9

    Default Re: filter/pump problems - pool newbie

    Last night I backwashed once and then put 4lbs of DE in (it says my filter requires 5lb so I figured 4 was good after a backwash?). Of course something else went wrong. The replacement hose I used started collapsing on itself from the pressure! How annoying. I used braided PVC (I think that what it's called) which I saw on some pumps at the pool store. So I have to replace that now. arhg

    The water doesn't seem THAT dirty to me but it is pretty cloudy. It's blueish though not green. The chlorine level is another problem, so far I've put several pounds of extra strenght shock in and the Chlorine still shows as nonexistant when you test the water.

    Yep I'm actually in North Coventry (which is chester co) but yeah I know Downingtown pretty well (grew up in Chester Springs).

+ Reply to Thread

Similar Threads

  1. newbie problems
    By camastown in forum Pool Chemicals & Pool Water Problems
    Replies: 1
    Last Post: 07-07-2012, 01:35 PM
  2. Filter/Pump Unlevel - Problems & Questions
    By jmaj43 in forum Pool Equipment & Operations
    Replies: 4
    Last Post: 08-03-2009, 07:46 PM
  3. pump and filter problems
    By pamelal41 in forum Pool Equipment & Operations
    Replies: 4
    Last Post: 03-03-2009, 07:54 PM
  4. Pool stored...oversized pump, huge filter, newbie questions
    By Mom2Czars in forum Pool Equipment & Operations
    Replies: 4
    Last Post: 07-25-2006, 08:58 PM
  5. Newbie pump/sand filter AIR question
    By famdog in forum Pool Equipment & Operations
    Replies: 2
    Last Post: 06-01-2006, 09:20 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts