Ok, two threads on the same topic is a no-no. Don't do that.
Ok, two threads on the same topic is a no-no. Don't do that.
Carl
Sorry, posted the other topic in the wrong spot, and what I'm after has changed. I think this is probably the thread to use, and the other should be locked or deleted. My bad.
I assumed that since the previous owners of the house (my in-laws) had a 1.5 HP motor in there previously, that what we should have replaced the old pump with the same size. I don't know if that is a correct assumption, now that I've been doing some digging on the topic. It seems as if 1.5" PVC pipe is going to be the limiting factor, and that anything over 1 HP could well be doing more harm to the motor than good?
Does this sound correct, that 1.5" pipe is going to allow for the maximum flow rate of 44 gpm, while my pool probably needs a minimum flow of about 54 gpm (26,000 g/8 hrs, and then divided by 60 min to get the max flow rate.) From what I'm seeing, it sounds like a 1 HP motor would put me in the ballpark of 40 gpm, depending on which motor I get.
As far as the current motor, smoke was emanating from this hole near where the wire enter the back of the motor. I don't see any scorching on the wires, I've tested for voltage on both legs of the wiring (it's 230v), and the motor is set to 230v.
IMG_1366.jpg
26,000 gal IG vinyl liner pool (20'x40'), Waterway SMF-110 wet end w/ Century SQS-1072R motor, Pac-Fab Triton TR60 sand filter, K-2006A. Manually added chems: 12.5% NaClO liquid, granular CYA, baking soda, 31% muriatic acid.
While we're at it, my pump runs 24/7. Does that change the calculation for how many gallons need to be filtered per 8 hours? We don't really use it that often to need it to be cleaned 3x per day... or does that mean we probably ought to consider putting in a timer to limit how much it runs?
26,000 gal IG vinyl liner pool (20'x40'), Waterway SMF-110 wet end w/ Century SQS-1072R motor, Pac-Fab Triton TR60 sand filter, K-2006A. Manually added chems: 12.5% NaClO liquid, granular CYA, baking soda, 31% muriatic acid.
26,000 gal IG vinyl liner pool (20'x40'), Waterway SMF-110 wet end w/ Century SQS-1072R motor, Pac-Fab Triton TR60 sand filter, K-2006A. Manually added chems: 12.5% NaClO liquid, granular CYA, baking soda, 31% muriatic acid.
Smoking motor is not good.
AG pumps are designed to run with the pool water higher up so there is gravity pressure. An IG pump is able to pump from the surface and pump the water up.
Further, most AG pumps are "up-rated" while IG pumps tend to be "full-rated". To super-simplify, it means that an AG pump rated at 1.5HP may have the same flow rate as a 3/4HP IP pump.
Re-read mas985's post above.
Carl
OK, re-reading mas985's post. I think I understand it a bit more now that I did before... and now I think I might just benefit from going to a SMALLER motor and impeller after looking at the spec sheet for my pump. To answer his original question though, I thought I might need a bigger motor because I was seeing debris just float by my skimmer, so I thought maybe there wasn't enough suction to properly skim the pool?
To the specs: http://www.waterwayplastics.com/prod...d-pumps/smf-2/
According to their flow rate chart, the 1 HP motor I've had might just be too big. 40 ft of head for the skimmer line = 75 gpm flow rate, and that's higher than the rating on my filter. FWIW, I've got 25 feet of head to the other suction line.
I guess I'd be looking more at the 3/4 HP pump now, based on the flow rate chart. This is all assuming that I'm calculation my GPM's correctly (54 gpm to turn over the pool in 8 hours, 60 gpm flow rate of the filter, 44 gpm per suction line x2) Based on all of that, would I be correct in choosing a 3/4 HP pump instead? If I were to get a replacement 3/4 HP motor, would I also need to get a different impeller as well?
Thanks for all the help on this, BTW. Last year I got a crash course on chemicals, and now I'm getting a crash course on the mechanical aspects of pool ownership!
26,000 gal IG vinyl liner pool (20'x40'), Waterway SMF-110 wet end w/ Century SQS-1072R motor, Pac-Fab Triton TR60 sand filter, K-2006A. Manually added chems: 12.5% NaClO liquid, granular CYA, baking soda, 31% muriatic acid.
mas985 is far better at figuring the mathematics of head to gpm to filter rate than I am.
Carl
Bookmarks