Results 1 to 10 of 18

Thread: Start-up with Quartzscape

Hybrid View

  1. #1
    Join Date
    Jul 2014
    Location
    Tx
    Posts
    24

    Default Re: Start-up with Quartzscape

    Started pump today and immediately put in 2 boxes of borax, 1lb of cal-hypo, and 1 gal of bleach. Borax and cal-hypo diluted in bucket (separately) and slowly poured in skimmer.
    Swept pool and scooped out a few leaves. 2 hrs later got the following readings:
    FC= 0
    CC=2
    pH= off scale and very yellow
    Alkalinity= 10
    Calcium hardness= 210

    Put in 1 more box of borax and 1 more gallon of bleach. Will take another set of readings tomorrow.

    Can't believe the FC is still zero. Could the low pH be causing a false FC reading??
    Should I be worried abt the alkalinity? Maybe pick-up some baking soda?

  2. #2
    BigDave's Avatar
    BigDave is offline Lifetime Member Whizbang Spinner BigDave 3 stars BigDave 3 stars BigDave 3 stars
    Join Date
    Jul 2010
    Location
    New Jersey
    Posts
    1,932

    Default Re: Start-up with Quartzscape

    TA will come up as pH comes up. Keep at it with a couple boxes of borax at a time (wait an hour between doses, pump running) until pH gets into 7-8 range then start halving the doses. I think that the CH increase is the result of the acid bath. Keep adding bleach.

  3. #3
    Join Date
    Jul 2014
    Location
    Tx
    Posts
    24

    Default Re: Start-up with Quartzscape

    Checked FC and pH after work. FC=0 and pH is still offscale (<7)..
    Added 1 more box of borax and 2 gallons of bleach into the skimmer. Swept pool. Filled a couple of old sport socks with 4 lbs (total) of dry CYA and hung in front of an outlet.
    2 hrs later: FC=5 and pH almost on scale now. Added 1/2 box of borax and went inside. Still running pump 24 hrs.

    High temps here are abt 102 degs and very sunny. Not expecting to see much FC by tomorrow evening.

    I have a chlorine dispenser that holds ~7 pucks. Should I be using that? The installer said the pucks can be hard on new plaster but wasn't sure abt Quartzscape.

  4. #4
    Join Date
    Jul 2014
    Location
    Tx
    Posts
    24

    Default Re: Start-up with Quartzscape

    Finally got my pH up to 7.2, but keeping FC levels up has been tough. Dumped a gallon of bleach in this morn so we could go for a swim. By the afternoon, FC was back to zero. The solid CYA in the sock trick works well. It was dissolved in abt 48 hrs. Need to get more. I loaded up the chlorine dispenser with some pucks to try an keep some FC (and a little more CYA) in the pool during the week. Thx for all the help.

  5. #5
    Watermom's Avatar
    Watermom is offline SuperMod Emeritus Quark Inspector Watermom 4 stars Watermom 4 stars Watermom 4 stars Watermom 4 stars Watermom 4 stars Watermom 4 stars
    Join Date
    Dec 1969
    Location
    Charleston, WV
    Posts
    9,345

Similar Threads

  1. I know NOTHING! Where do I start?
    By lbmoore in forum Testing and Adjusting Pool Water Chemistry
    Replies: 20
    Last Post: 06-26-2011, 12:19 AM
  2. Day 1, where to start?
    By sturev in forum Testing and Adjusting Pool Water Chemistry
    Replies: 7
    Last Post: 06-05-2010, 05:34 PM
  3. Quartzscape? Is it good?
    By kmmlangston in forum In-Ground Pool Construction and Repair
    Replies: 1
    Last Post: 06-02-2010, 01:03 PM
  4. Sand filter changed @ start of season ? HIGH PRESSURE @24 PSI FROM START
    By timmygreene in forum Pool Equipment & Operations
    Replies: 8
    Last Post: 05-21-2010, 07:48 AM
  5. start up ?
    By Bergerman in forum Pool Startup, Shutdown, & Winter Operation
    Replies: 3
    Last Post: 04-29-2007, 12:41 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts