+ Reply to Thread
Page 2 of 9 FirstFirst 1 2 3 4 ... LastLast
Results 11 to 20 of 89

Thread: Iron in water source

  1. #11
    Join Date
    Jul 2013
    Location
    Northern Illinois
    Posts
    817

    Default Re: Iron in water source

    Good for you! BTW, PoolDoc's Dad passed yesterday so you might not hear from him directly for a while. Let us know if you need help! Sounds like you are on the right track although I am a bit surprised that your backwash discharge is just white. White from Calcium but I think it would have an orange-ish tint from the iron. What color is your water now?
    26K gal 20x40 rectangular IG vinyl pool; Apr 2014: New pump, liner, auto-cover, & water; Pentair Whisperflo 1HP pump; Pentair Trition sand filter; Cover/Star CS-500 auto cover; Taylor K-2006C; OTO

  2. #12
    Join Date
    Aug 2014
    Location
    Virginia
    Posts
    36

    Default Re: Iron in water source

    I saw PoolDoc's post. Good looking family. I'm sorry for his loss, losing a parent is never easy.
    Pool water is clear with a greenish tint. Still a significant amount of "rust" colored sediment on bottom.
    22,000 gal. 30' round IG, vinyl liner, sand filter, 1 HP pump, BBB method
    Taylor K2006c & K1000

  3. #13
    Join Date
    Aug 2014
    Location
    Virginia
    Posts
    36

    Default Re: Iron in water source

    F/U
    Had to correct pH again this morning. Sediment seems to go back into solution with lowering the pH and water now green.
    Adequate HEPD?
    22,000 gal. 30' round IG, vinyl liner, sand filter, 1 HP pump, BBB method
    Taylor K2006c & K1000

  4. #14
    Join Date
    Jul 2013
    Location
    Northern Illinois
    Posts
    817

    Default Re: Iron in water source

    .
    Hey. I am not an expert here (for sure!). I have been a pool owner/operator for many years so there are some things I know pretty well. However, I am new to the BBB method so there are tons of things I don't know very well. BUT I want to keep a conversation going in the hopes of attracting a moderator/expert, so let's keep talking.

    Are you continuing with the cal-hypo/backwashing and the 1 cup Polyquat every other day too?

    -HEDP is yucky stuff and it stays in the water for a while. I would hesitate to add more only because the purpose behind using it IS to get metals in solution and it sounds like that is what's happening.

    Quote Originally Posted by PoolDoc View Post
    You can use cal hypo tabs... in the skimmer -- ONLY in the skimmer -- to remove iron and place it on the calcium residue from the cal hypo, which is then trapped by the filter.
    As I understand it, the iron must be in solution for this to work. I used this same process with my iron-loaded new fill water and I am now metal-free!

    I might suggest also that you go into "settings" and create a signature with your pool info. It helps the mods so they don't have to scroll back to see your pool specs.
    http://www.poolforum.com/pf2/showthr...ignature-line!
    26K gal 20x40 rectangular IG vinyl pool; Apr 2014: New pump, liner, auto-cover, & water; Pentair Whisperflo 1HP pump; Pentair Trition sand filter; Cover/Star CS-500 auto cover; Taylor K-2006C; OTO

  5. #15
    BigDave's Avatar
    BigDave is offline Lifetime Member Whizbang Spinner BigDave 3 stars BigDave 3 stars BigDave 3 stars
    Join Date
    Jul 2010
    Location
    New Jersey
    Posts
    1,932

    Default Re: Iron in water source

    A couple things I've noticed in this thread.
    @FormerBromineUser: I think the HEDP is intended to keep the iron in solution.
    @stochen: I think the idea is to let the pH stay high and create a high pH / high chlorine zone in the skimmer so the iron comes out on the filter with the calcium. When you drop the pH, you might redissolve the iron that's in the filter. Perhaps drop it no lower than 7.8. Can you vacuum the orange stuff.
    12'x24' oval 7.7K gal AG vinyl pool; ; Hayward S270T sand filter; Hayward EcoStar SP3400VSP pump; hrs; K-2006; PF:16

  6. #16
    Join Date
    Jul 2013
    Location
    Northern Illinois
    Posts
    817

    Default Re: Iron in water source

    BigDave: Glad you're here

    Yes, the HEDP is to keep the iron in solution and it sounds like that's what stcohen is describing as happening.
    Do you think he needs to add more?

    I saw Ben's references (quoted below) about chlorine.
    Quote Originally Posted by PoolDoc View Post
    Clean the skimmer basket, then add 1 - 2 cal hypo tabs in to the skimmer... Don't add more than 1/2 pound per day.
    Quote Originally Posted by PoolDoc View Post
    The problem you have is that adding chlorine to a pool full of iron tends to make staining inevitable. Ideally, you need to remove the iron BEFORE you begin chlorinating. BUT, you can't let the pool become a slime pit during this period.
    All I found about pH is below. I'm wondering about raising pH to 7.8...:
    Quote Originally Posted by PoolDoc View Post
    ...adjust your pH to near 7.0 . . . but NOT lower.
    26K gal 20x40 rectangular IG vinyl pool; Apr 2014: New pump, liner, auto-cover, & water; Pentair Whisperflo 1HP pump; Pentair Trition sand filter; Cover/Star CS-500 auto cover; Taylor K-2006C; OTO

  7. #17
    BigDave's Avatar
    BigDave is offline Lifetime Member Whizbang Spinner BigDave 3 stars BigDave 3 stars BigDave 3 stars
    Join Date
    Jul 2010
    Location
    New Jersey
    Posts
    1,932

    Default Re: Iron in water source

    I'm pretty sure bringing the pH down was to get and keep the iron in solution to start then use HEDP to try to keep it in solution.

    I believe the mechanism for removing iron with cal-hypo is to let the cal-hypo raise the pH causing the iron to drop out on the filter with the calcium precipitate. I would backwash before dropping the pH. Did you do it that way already or did you backwash after dropping the pH?.

  8. #18
    Join Date
    Aug 2014
    Location
    Virginia
    Posts
    36

    Default Re: Iron in water source

    Yes, I am continuing with the cal-hypo/backwashing and the 1 cup Polyquat every other day. 3rd dose polyquat today.
    BigDave, that makes sense, I think I did it that way but I will make sure to backwash before dropping the pH again.
    Thanks,
    22,000 gal. 30' round IG, vinyl liner, sand filter, 1 HP pump, BBB method
    Taylor K2006c & K1000

  9. #19
    BigDave's Avatar
    BigDave is offline Lifetime Member Whizbang Spinner BigDave 3 stars BigDave 3 stars BigDave 3 stars
    Join Date
    Jul 2010
    Location
    New Jersey
    Posts
    1,932

    Default Re: Iron in water source

    I haven't seen a recent pH or chlorine reading. How are you with chlorine?

    Is the water clear but green or opaque green?
    12'x24' oval 7.7K gal AG vinyl pool; ; Hayward S270T sand filter; Hayward EcoStar SP3400VSP pump; hrs; K-2006; PF:16

  10. #20
    Join Date
    Aug 2014
    Location
    Virginia
    Posts
    36

    Default Re: Iron in water source

    This am pH 7.4, FC >5, water somewhat opaque green.
    Have to leave until Fri. am. Will of course keep filter running; backwash and retest on return.
    22,000 gal. 30' round IG, vinyl liner, sand filter, 1 HP pump, BBB method
    Taylor K2006c & K1000

+ Reply to Thread

Similar Threads

  1. Iron In My Water
    By Phenom300 in forum -- Subscriber Posts --
    Replies: 3
    Last Post: 08-16-2014, 09:18 PM
  2. Iron out to treat iron and tea colored water
    By Fornetti in forum --cleanup--
    Replies: 0
    Last Post: 07-02-2013, 03:56 AM
  3. Well Water very High Iron
    By meadsrm in forum Pool Chemistry for Intex-type Pools
    Replies: 2
    Last Post: 06-05-2012, 03:58 PM
  4. New Pool Owner With High Iron Manually Removing Iron
    By labdi01 in forum Dealing with Stains & Metals, . . . and 'Minerals' & 'Ions',
    Replies: 35
    Last Post: 06-18-2010, 03:56 PM
  5. Aerating Water to Get Rid of Iron
    By smallpooldad in forum Testing and Adjusting Pool Water Chemistry
    Replies: 6
    Last Post: 09-27-2006, 10:59 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts