+ Reply to Thread
Results 1 to 10 of 16

Thread: Using Muriatic Acid to Safely Lower Your Pool's pH

Hybrid View

  1. #1
    PoolDoc's Avatar
    PoolDoc is offline Administrator Quark Inspector PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars
    Join Date
    Jan 2005
    Location
    Georgia
    Posts
    11,386

    Default Using Muriatic Acid to Safely Lower Your Pool's pH

    .

    __________________________________________________
    Using Muriatic Acid Safely:

    Product Description
    20 degree Baume' 31.45% Muriatic Acid AKA hydrochloric acid AKA "MA"
    Avoid diluted (15%) or low-fume acid, since they often contain OTHER chemicals that may mess up your pool! Of course, if you are 100% sure the only ADDED chemical is water, 15% acid is fine.
    MSDS - Material Safety Data Sheets for muriatic acid
    Hasa Pool
    http://www.whatsinproducts.com//file...tic%20Acid.pdf
    Sunnyside Corp
    Sources:
    Crown Muriatic Acid at Lowe's
    TransChem Muriatic Acid at some Ace Hardware stores
    Other sources: Any hardware, building supply, or home care store is a possible source. Brands may vary, even within a single chain.

    Dewalt Safety Glasses (Amazon)
    Large black nitrile gloves(Amazon)
    __________________________________________________
    Step by step:

    Video demonstration of these steps: http://youtu.be/ajC-OROORko
    This is the preliminary unedited video, without voice-over and graphics, but it completely demonstrates the correct method.

    # 1 - Make sure your pool pump is on, and leave it on for at least 1 hour after you add acid.

    # 2 - Get a sharp stainless kitchen paring knife, plastic gloves and some sort of glasses BEFORE opening the bottle. Put on the gloves and glasses.

    # 3 - Splash some water on the pool deck, place the bottle in the puddle on the deck, and remove the lid.

    # 4 - Either gently pull the seal from the bottle OR use the knife to cut it away. If you use the knife, immediately rinse the blade in the pool.

    # 5 - Once the lid is off, and the seal removed, take the bottle and submerge it partially in the pool.

    # 6 - Pour the acid into the pool by tilting the bottle. Keep the mouth of the bottle only a couple of inches above the pool's surface.

    # 7 - Your basic dose is 1/4 of a 1 gallon bottle per 10,000 gallons of pool water. Do NOT try to measure this! Under-guesstimate the dose, and add more later if needed. (Pouring acid from one container to another will release a LOT of noxious fumes!)

    # 8 - Cap the bottle tightly.

    # 9 - Store the bottle outside in an opaque plastic container. If you do store the acid indoors, be sure to put inside a sealed heavy duty garbage bag. Read the explanation, below.

    #10 - Rinse any spills off you or the deck promptly with pool water. If you should splatter the acid in your eyes, let go of the bottle and IMMEDIATELY roll over into the pool. Open your eyes underwater, and swim away from the area where you have added acid. This will flush your eyes completely and safely. (If you can't swim, move a few feet away from your work area, lay on the deck and submerge your head in the pool. Force your eyes open in the water.)

    #11 - Never, NEVER use a hose with a nozzle to rinse your eyes -- a high pressure stream of water can also do immediate, serious damage to your eye. If for some reason, you cannot put your face in the water, move a hose with NO NOZZLE next to you BEFORE you begin adding acid. Turn on the water so that it flows gently out of the hose, and LEAVE IT RUNNING till you have re-sealed and rinsed the bottle of acid. If you should have a problem, use the hose to flush your eyes.

    __________________________________________________
    Explanations:
    Any acid can be used to lower your pool's pH or alkalinity, but some are better than others. Organic acids, like ascorbic acid (Vitamin C) or citric acid (lemon juice) are used to remove stains -- but they are destroyed by chlorine and are expensive. The most common 'pool acids' ("pH Minus", "pH Down", etc.) are based on sodium bisulfate, a partially neutralized form of sulfuric acid. However, sulfates increase concrete corrosion, and sodium bisulfate is expensive, compared to muriatic acid.

    We usually recommend hydrochloric acid, called "muriatic acid" when sold for commercial purposes, for use instead except on very small pools. There are several reasons:
    + it is cheaper than sodium bisulfate.
    + it does not add sulfates, which are damaging to inground concrete pools.
    + it does add chlorides, which are desirable in pools with SWCG.

    But muriatic acid is not perfect.

    It is perfectly safe for you and your pool, once it's diluted. But until then, because it is so strong, it can be VERY damaging. Like several pool chemicals (including bleach, powdered forms of chlorine, and sodium bisulfate) it can cause permanent eye damage almost instantly. It will discolor or damage almost anything you get it on, and will burn your skin quickly. So, you have to be very careful how you handle it. Fortunately, it's not hard to handle it correctly -- just follow the directions above!

    It has one unique hazard, however.

    Unlike most other common acids, hydrochloric acid is actually a gas in its pure form (HCl). For use, it's dissolved in water. But, at the concentration sold and labeled muriatic acid (~31%) the gas -- HCl -- will try to leave the water. This gas is painful to breath, and can be dangerous. It is EXTREMELY damaging to copper wiring or bare metal. If you follow the handling instructions above, you'll avoid breathing the fumes. But you MUST also be very careful how you store the acid, once you've unsealed the bottle. You must NOT store the acid in your garage or pump room, simply with the cap on. Enough fumes will often leak out to damage nearby metal or wiring. If at all possible, store it outside in a small covered plastic garbage can.
    __________________________________________________
    If you must store muriatic acid inside do this:
    # 1 - After use, cap the bottle tightly.
    # 2 - Rinse the entire bottle off in the pool.
    # 3 - Place the bottle inside a heavy duty garbage bag, and then seal the bag with a twist tie.
    # 4 - You may then store the bottle inside.
    # 5 - When you next use the bottle, carry the bag and bottle outside BEFORE opening the bag. That way, any fumes that have accumulated can dissipate harmlessly.

    __________________________________________________
    .
    Last edited by PoolDoc; 05-30-2018 at 07:28 PM.

  2. #2
    Join Date
    Jul 2010
    Location
    Largo, Florida
    Posts
    509

    Default Re: Using Muriatic Acid to Safely Lower Your Pool's pH

    Nice! Until recently, I was not following step 7.

    What do the chlorides do in a swcg pool?
    rectangle 11.5K gal IG concrete pool;; 125sf cartridge filter; 2hp 1 speed pump; K-2006, k-1766; PF:10

  3. #3
    PoolDoc's Avatar
    PoolDoc is offline Administrator Quark Inspector PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars PoolDoc 5 stars
    Join Date
    Jan 2005
    Location
    Georgia
    Posts
    11,386

    Default Re: Using Muriatic Acid to Safely Lower Your Pool's pH

    -Cl - (2e) => +Cl or 'pool chlorine'.

    In other words, your SWCG uses chlorides to make chlorine (-Cl -> +Cl)

  4. #4
    Join Date
    Jul 2011
    Location
    garden city, ks
    Posts
    24

    Default Re: Using Muriatic Acid to Safely Lower Your Pool's pH

    Thanks for the info.!

    After the read, ( a couple of times) it makes perfect sense to Me.

    Gary
    POOL SPECS: In-ground vinyl; 18 x 36' 24,000 Gallon,

  5. #5
    chem geek is offline PF Supporter Whibble Konker chem geek 4 stars chem geek 4 stars chem geek 4 stars chem geek 4 stars
    Join Date
    Nov 2004
    Location
    California
    Age
    65
    Posts
    2,226

    Default Re: Using Muriatic Acid to Safely Lower Your Pool's pH

    You can often buy 15% Muriatic Acid and if you can get it for roughly half the price of 31.45% Muriatic Acid then it's about as economical. I find that this half-strength fumes a LOT less. Nevertheless, my pool store sells the full-strength at the best price so I still use that and am just careful to be up-wind when pouring. I do measure it in a cup, but I do that pouring away from my face and over the pool.

    The good news is that though the fumes are irritating, this is actually a good thing since it warns you well in advance of being too harmful. Nevertheless, it's the nastiest stuff most pool owners will experience with regard to chemicals.

  6. #6
    Join Date
    May 2010
    Location
    Arizona
    Posts
    255

    Default Re: Using Muriatic Acid to Safely Lower Your Pool's pH

    Quote Originally Posted by chem geek View Post
    You can often buy 15% Muriatic Acid and if you can get it for roughly half the price of 31.45% Muriatic Acid then it's about as economical. I find that this half-strength fumes a LOT less. Nevertheless, my pool store sells the full-strength at the best price so I still use that and am just careful to be up-wind when pouring. I do measure it in a cup, but I do that pouring away from my face and over the pool.

    The good news is that though the fumes are irritating, this is actually a good thing since it warns you well in advance of being too harmful. Nevertheless, it's the nastiest stuff most pool owners will experience with regard to chemicals.
    It has been my experience here in Arizona that the full strength (31.45%) Muriatic acid is sold almost exclusively by pool stores, while the Grocery stores and Hardware stores sell the 15% strengths. It is also my experience that both strengths are not that far apart in price.
    If you can afford a swimming pool and computer, you can probably afford to help keep the PoolForum alive. Please be a responsible member and subscribe today. You'll probably save more than the membership fee on your first trip to the pool store. BTG

+ Reply to Thread

Similar Threads

  1. Muriatic Acid w/ Vinyl pool
    By gdubs in forum Using Chlorine and Chlorinating Chemicals
    Replies: 9
    Last Post: 08-25-2009, 07:06 PM
  2. adding muriatic acid to covered swg pool
    By lauralou in forum Salt Generators (SWCG) & other Chlorine Feeders
    Replies: 4
    Last Post: 04-25-2009, 10:36 PM
  3. Lowering TA with Dry Acid Or Muriatic Acid
    By CelticDaddio in forum Dealing with Alkalinity and Calcium
    Replies: 30
    Last Post: 07-05-2007, 01:54 AM
  4. How much much muriatic acid do I add to lower the PH?
    By CelticDaddio in forum Testing and Adjusting Pool Water Chemistry
    Replies: 4
    Last Post: 05-13-2007, 08:19 PM
  5. Pool store advice to lower alkalinity - three day muriatic acid dose method
    By aquarium in forum Dealing with Alkalinity and Calcium
    Replies: 14
    Last Post: 07-03-2006, 11:04 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts