+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 18

Thread: Question-How Reduce Power Costs?

  1. #1
    Join Date
    Mar 2006
    Location
    Katy, Texas, USA
    Posts
    30

    Default Question-How Reduce Power Costs?

    Advice please, new to pools, had ours (~26,000 USG salt water) 10 months now. Power rates here in Texas went up ~50% this winter, not looking forward to power bill for AC & pool this summer !

    Read tips on www.poolsolutions.com including one on mail filter pump HP and power costs, I have "standard" 2.0 HP main filter pump (Pentair WhisperFlo Model WF-28, Service Factor = 1.1) and probably small plastic lines between pump and pool and thus high backpressures due to friction et al. Not good.

    1) Curious (as too late to change), how do I measure pipe sizes is it OD or ID?

    2) To reduce power cost assume I assume not worth changing this "big" pump out as less than 1 year old?

    3) Water circ back to pool via white plastic nozzles at sides of pool and in spa that are screwed onto the plastic pipes. Seems to me that if I removed these nozzles then back pressure would be significantly less and thus pump volume would be significantly higher and thus I could run pump less per day?

    4) OK so removing nozzles would be unsightly, how about I just drill them out to 1" holes?

    5) Any other power saving ideas?

    Thanks in advance . . .
    Last edited by Katy-Texas; 03-26-2006 at 03:37 PM.

  2. #2
    Join Date
    Dec 2004
    Location
    Round Rock, Texas, USA.
    Age
    67
    Posts
    35

    Default Reduce power cost options

    I live in Round Rock Texas, and last fall I switched from TXU to "Direct Energy". The rates from the same pole are about 20% lower after the switch.

    Also see my post in this section about 2 speed motors. Upgrading to a 2 speed motor will have a fast payback period. Just increase your pump on time to move the same volume of water every day. Look at the curves on competitive pumps. Lowering the pump backpressure at low speed helps the water flow better, so the GPM reduction at low speed is not nearly as dramatic as the speed reduction of your electric meter.

    Use high speed for extra skimmer suction, bottom feeders, vacuuming, but not every day.

    Just pay attention to the low speed priming issue.

    I think that this 2 speed motor idea is as big a secret as using bleach, borox, and baking soda as compared to a dump truck full of chemicals ($$$$) from the pool store.

    Jim

  3. #3
    Join Date
    Mar 2006
    Location
    Katy, Texas, USA
    Posts
    30

    Default

    Jim, thanks for support.

    Power supplier, good point, I live in Katy Texas and used www.powertochoose.com and my zip code to compare power rates and switched from Reliant to Gexa Energy which is also is cheaper I think than Direct Energy, plus wehen I signed up for auto monthly billing against my credit card they gace me 2000 Continental Airmiles plus airmiles for each monthly charge. Problem is all the providers rates went up significantly this winter.

  4. #4
    Join Date
    Dec 1969
    Location
    Katy, TX
    Posts
    336

    Default

    Quote Originally Posted by Katy-Texas
    I live in Katy Texas
    Not to threadjack, but howdy neighbor!

    Michael

  5. #5
    mas985's Avatar
    mas985 is offline Lifetime Member Whizbang Spinner mas985 3 stars mas985 3 stars mas985 3 stars
    Join Date
    Dec 2004
    Location
    Pleasanton, CA
    Posts
    1,423

    Default

    Answers to your questions:


    1) Curious (as too late to change), how do I measure pipe sizes is it OD or ID?

    ID but usually not exact to the pipe size.

    2) To reduce power cost assume I assume not worth changing this "big" pump out as less than 1 year old?

    It could still be worth it. Especially if you can get a rebate from the power company. Some states offer up to $300. Even so, pay back could be less than 2 years.

    3) Water circ back to pool via white plastic nozzles at sides of pool and in spa that are screwed onto the plastic pipes. Seems to me that if I removed these nozzles then back pressure would be significantly less and thus pump volume would be significantly higher and thus I could run pump less per day?

    Yes, you could first try to remove them and see if your pressure gauge drops.

    4) OK so removing nozzles would be unsightly, how about I just drill them out to 1" holes?

    You may want to see if you can purchase new fittings first. If you cannot, then consider drilling them out. Most returns are 1", so it seems odd that they are so small.

    5) Any other power saving ideas?

    My guess is your turnover rate is about 3 hours? If so, try running the pump for only 3 hours a day. 6 during heavy swimmer loads.


    Mark

  6. #6
    Poconos is offline SuperMod Emeritus Whizbang Spinner Poconos 4 stars Poconos 4 stars Poconos 4 stars Poconos 4 stars Poconos 4 stars Poconos 4 stars
    Join Date
    Dec 1969
    Location
    Honesdale PA
    Posts
    1,812

    Default Something to consider

    Just a simple thing and not very significant. When the pressure increases the power consumption (current) to the pump decreases. Try putting a clamp-on ammeter on the pump line and see what happens. Look at the current (amps) full flow then blocked. Turns out that when the flow is totally blocked the power consumption is at a minimum. No water flow = no work done = low power consumprion. Specific to a centrifugal pump. On to the issue....I bored my return nozzles out to cut the pressure but I also know I don't have to run the system as long and therefore save some energy. Me thinks we're talking details that won't make much difference in the monthly $$ electric bill. As much as I'm being a monkey and tracking all this stuff, I haven't done it for this issue. So.....just my thinking and fodder for discussion.
    Al

  7. #7
    CarlD's Avatar
    CarlD is offline SuperMod Emeritus Vortex Adjuster CarlD 4 stars CarlD 4 stars CarlD 4 stars CarlD 4 stars CarlD 4 stars CarlD 4 stars
    Join Date
    Dec 1969
    Location
    North Central NJ
    Posts
    6,607

    Default

    Good suggestions! 2 speed pumps are the way to go! How many gallons is your pool? 2hp sounds HUGE. I run a 20,000 gallon pool with solar heat on a 1 hp Super Pump (Hayward) and I run it on low-speed 99% of the time.
    Carl

  8. #8
    Join Date
    Nov 2004
    Location
    Orlando, Florda, USA.
    Posts
    26

    Default

    Now I'm concerned about my pump.

    Our pool is close to being done and the builder has a 2.5 HP Hayward Super 2 pump setup.

    We have a Hayward DE 6020 Filter. A Rock waterfall, 3 foot shear decent fall, 4 returns, 2 spa jets (in pool), skimmer and vac line. Will be getting solar later this year (9 - 10 panels).

    Pump is same ground level as pool and furthest point away from pump is maybe 100 feet. PVC pumbing is 2". Pool also is 15 X 30 freeform but only 3 ft to 5.6 feet deep. I'm guessing gallons at maybe 13K.

    Should I have builder take out pump and replace with smaller, or can I (as some said in this thread) simply run the pump for only 3 hours a day.

    I should also say salesman told me I "didn't" want a 2 speed pump when we were getting started.

    Thanks for any advice.


    W Bell
    Orlando, FL

  9. #9
    mas985's Avatar
    mas985 is offline Lifetime Member Whizbang Spinner mas985 3 stars mas985 3 stars mas985 3 stars
    Join Date
    Dec 2004
    Location
    Pleasanton, CA
    Posts
    1,423

    Default

    Because of the water features and vac line, you will need heavy flow some of the time. This means you have two choices, multiple pumps or a 2-speed pump. For a 2-speed pump, the turnover time is twice as long as that of the high speed but the energy use is about a third. So overall energy savings is about 30%. Going form a 2.5 Hp to a 1 Hp pump will save you close to the same (depending on pump) but you may still need a bigger pump for the features and vac. So either way, you should have significant savings which will pay for itself in not too much time at all.

  10. #10
    kaybinster Guest

    Default Two more options

    If your utility offers it, you might want to switch to time of day billing. Obviously you will need to do an analysis of how much electricity you use at various times of day. In NJ, time of day billing gives you cheap power during off-peak in exchange for expensive power peak periods which are M-F 9am-9pm. I have an electric heat pump to heat the pool and run the pump and the heat pump at night and on weekends when power is cheap.

    Another option is to install a PV solar electric system to generate your own power. I have a 10 kw system which generates about 12,000 kwh a year. Check out the threat on solar water heating where I described the system in more depth.

+ Reply to Thread

Similar Threads

  1. high cya, how to reduce it?
    By gvon79 in forum Using Chlorine and Chlorinating Chemicals
    Replies: 4
    Last Post: 06-11-2011, 06:34 PM
  2. Does a DE Filter help reduce chlorine use
    By smallpooldad in forum Pool Equipment & Operations
    Replies: 0
    Last Post: 05-08-2008, 11:51 PM
  3. Does a solar cover help reduce algae growth??
    By MTU 5.0 in forum Dealing with Algae & Slime
    Replies: 8
    Last Post: 07-26-2006, 11:49 AM
  4. I want to shock to reduce chloramines but....
    By cruzmisl in forum Using Chlorine and Chlorinating Chemicals
    Replies: 5
    Last Post: 06-26-2006, 06:57 PM
  5. Reduce Chemical Usage 30-50% while stabalizing pH ;-)
    By Bleach=Chlorine? in forum Salt Generators (SWCG) & other Chlorine Feeders
    Replies: 18
    Last Post: 06-13-2006, 10:07 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts