+ Reply to Thread
Results 1 to 6 of 6

Thread: How Do You Start The BBB Method from a Fresh Refill?

Hybrid View

  1. #1
    Join Date
    May 2011
    Location
    San Antonio, TX
    Posts
    16

    Default Re: How Do You Start The BBB Method from a Fresh Refill?

    Thanks guys. Refill is complete and water is circulating. Only had time to test for the following this morning:

    Chlorine - basically 0 ppm
    pH - ideal
    CYA - basically none

    I do have tabs in the chlorinator. I'm planning on doing another backwash/DE replacement tonight.

    Sounds like I need to get bleach in ASAP and try to get CYA up too...

  2. #2
    CarlD's Avatar
    CarlD is offline SuperMod Emeritus Vortex Adjuster CarlD 4 stars CarlD 4 stars CarlD 4 stars CarlD 4 stars CarlD 4 stars CarlD 4 stars
    Join Date
    Dec 1969
    Location
    North Central NJ
    Posts
    6,607

    Default Re: How Do You Start The BBB Method from a Fresh Refill?

    Sounds good, but "ideal"is not really a reading. "ideal" pH can be anything from 7.2 to 7.8, but usually 7.3 to 7.6. If your pH is 7.5 or higher, the trichlor tabs are fine. Even if pH is lower, you can still use them but always have a box of Borax around so if pH dips to 7.0 or less you can immediately add the Borax and bring it back up. If your T/A is also very low, you can substitute Arm&Hammer Washing Soda for the Borax and it will bring up your T/A as well as the pH.

    In any case, when using Trichlor tabs, you need to watch your pH at LEAST daily and your CYA weekly.

    The one thing I like about Trichlor tabs in the spring or in a new fill is they erode. This means that you are getting a constant flow of chlorine into your water and there's no chance of FC dropping to zero.

    I opened to fairly high pH, green slime and no CYA. After a mega-dose of LC to clear most of it, I used up all my di-chlor, which adds CYA and lowers pH, but not as much as Trichlor, then filled up my floater with left over trichlor tabs. Over two weeks I raised my CYA to just over 30ppm, added two boxes of Borax and one of Washing Soda, and now have a stable pH of 7.6 (hasn't changed in almost 3 weeks), a CYA of 30ppm, an FC of between 3 and 5, and a TA of 60--yeah, that low. But, since my pH is stable, why should I mess with T/A? After all, its JOB is to keep pH stable!

    Carl
    Carl

  3. #3
    Join Date
    May 2011
    Location
    San Antonio, TX
    Posts
    16

    Default Re: How Do You Start The BBB Method from a Fresh Refill?

    Thanks Carl! I checked again and pH is sitting at 7.5.

    I just replaced the DE, and I'm about to add CYA in the skimmer. Tabs still in chlorinator, and going to put in 2 gallons of bleach tonight. Hopefully we'll get some Chlorine to stick around...

    Thanks! Mark

+ Reply to Thread

Similar Threads

  1. Fresh fill with city water - start with bleach or dichlor?
    By Mm_putnam in forum Testing and Adjusting Pool Water Chemistry
    Replies: 7
    Last Post: 05-27-2013, 01:22 PM
  2. Tested Water to Start BBB method
    By HollyClo in forum DPD-FAS based testing
    Replies: 19
    Last Post: 08-05-2011, 01:57 PM
  3. Wanting to start BBB method
    By knifechief13 in forum Testing and Adjusting Pool Water Chemistry
    Replies: 4
    Last Post: 07-02-2011, 06:52 PM
  4. refill - how to start water treament
    By fredg in forum Using Chlorine and Chlorinating Chemicals
    Replies: 5
    Last Post: 06-13-2011, 02:20 PM
  5. Start up process after refill
    By Phillbo in forum Salt Generators (SWCG) & other Chlorine Feeders
    Replies: 4
    Last Post: 04-05-2006, 11:42 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts