+ Reply to Thread
Results 1 to 9 of 9

Thread: Pump Will Not Maintain Its Prime

Hybrid View

  1. #1
    aylad's Avatar
    aylad is offline SuperMod Emeritus Burfle Ringer aylad 4 stars aylad 4 stars aylad 4 stars aylad 4 stars aylad 4 stars aylad 4 stars
    Join Date
    Dec 1969
    Location
    Northwest Lousiana
    Posts
    4,757

    Default Re: Pump Will Not Maintain Its Prime

    I know this is one of those "no-duh" things, but have you made sure that the water level in the skimmer is sufficient?

    Janet

  2. #2
    mas985's Avatar
    mas985 is offline Lifetime Member Whizbang Spinner mas985 3 stars mas985 3 stars mas985 3 stars
    Join Date
    Dec 2004
    Location
    Pleasanton, CA
    Posts
    1,423

    Default Re: Pump Will Not Maintain Its Prime

    A stuck wier door will also cause problems.
    Mark
    Hydraulics 101; Pump Ed 101; Pump/Pool Spreadsheets; Pump Run Time Study; DIY Acid Dosing; DIY Cover Roller
    18'x36' 20k plaster, MaxFlo SP2303VSP, Aqualogic PS8 SWCG, 420 sq-ft Cartridge, Solar, 6 jet spa, 1 HP jet pump, 400k BTU NG Heater

  3. #3
    Poconos is offline SuperMod Emeritus Whizbang Spinner Poconos 4 stars Poconos 4 stars Poconos 4 stars Poconos 4 stars Poconos 4 stars Poconos 4 stars
    Join Date
    Dec 1969
    Location
    Honesdale PA
    Posts
    1,812

    Default Re: Pump Will Not Maintain Its Prime

    I missed the intermittent part. That points to what Jan and Mark mentioned and not to an air leak. If the water is low and a vortex is forming in the skimmer and you don't want to add water then put a few small rocks or something in the skimmer basket to break up the flow pattern and you should be OK until the level gets higher. I don't have a weir 'door' but an older style floating circular one that sits in the basket. That has a tendency to stick at high water levels and do the same thing because the flow over the top and into the basket isn't enough to maintain full flow and I would get the same intermittent pumping action.
    Al
    16'x32' oval 22K gal IG vinyl pool; ; Hayward S244T sand filter; Hayward superpump 1 HP pump; hrs; K-2006; PF:5.5

  4. #4
    Join Date
    May 2010
    Posts
    12

    Default Re: Pump Will Not Maintain Its Prime

    First thing I did was check all of the above, except blockatge of the main drain. Too cold to get down there w/o a wet suit.

    My designated sheer descent pump is a little noisier than the others (same brand & size). Nothing that sounds horrible or something mechanically wrong, it's just more of a lower humming than the other two (especially at start-up), which wasn't the case before the problem occurred.

    Thanks for all of the above help and I'll let you know if I find something in the drain.

    Merry Christmas & a happy New Year to all.

+ Reply to Thread

Similar Threads

  1. New pump won't prime
    By ButchM1 in forum Pool Equipment & Operations
    Replies: 1
    Last Post: 05-17-2012, 11:32 PM
  2. can't keep prime in pump
    By PFPAM in forum Pool Equipment & Operations
    Replies: 5
    Last Post: 06-28-2007, 07:35 PM
  3. Can't get pump to prime
    By Pamsel in forum Pool Equipment & Operations
    Replies: 5
    Last Post: 07-07-2006, 09:47 AM
  4. Dead Pump: How to maintain chemistry?
    By Ken and Laura in forum Pool Chemicals & Pool Water Problems
    Replies: 2
    Last Post: 06-30-2006, 10:58 AM
  5. Pump problems... Hard to prime and air in the pump lines
    By tinyprotagonist in forum Pool Equipment & Operations
    Replies: 1
    Last Post: 06-29-2006, 10:38 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts