New from new york

Hello from upstate NY !!

Been a lurker for a while and decided to join...or should I say 'take the plunge" ....sorry..lol

Lots of great info and I hope to learn alot.

Thanks

Welcome! Glad to have you join us. Let us know if you have any questions that we can help with. :)

I actually have a filter dilemma....currently useing a Hayward Pro series s210t filter and have been told by many "pool" people that I will need to upgrade to a cartridge filter.
My current AG pool is 10k gallons and the pool I am having installed next week is a 27' round @ 18,5k gallons. According to the flow rate of the filter @ 20 gpm ....and the flow rate of my Pentair superflo pump @ 84 gpm, I'm a bit confused if this system will be ok.

The sand filter has always kept my water clear as far as I can tell.....I like the idea of a cartridge filter...less maintenance , more flow(turnover) etc...but not thrilled at the replacement filter prices.

Currently I have a line on a Jandy cl580...which was running a 40k gal pool .

I hate to spend $$$ thats not necessary but want a good system for my new pool.

any help or insight is appreciated

I appreciate the help

I wouldn't switch away from a sand filter. They are just too easy. Cartridge filters aren't bad if you live someplace arid with little organic debris (leaves, pollen, etc.) but in the northeast where you are, I'd stick with sand. Plus, cleaning cartridges is a big pain and a dirty job. I'm not the pump/filter expert around here. Let me ask someone else to give you advice on what to buy. Sit tight.

The more I think about it...the more I think sand is for me. It has worked flawlessly for me the past 7 seasons.

Just not sure if my current set up is sized right to clean my pool.

thanks for the help

On a 17k gallon pool, you would ideally have a flow rate of 36 GPM (8 hour turn-over). That translates into a 21" ID sand filter @ 15 GPM. You'd want a 18 sft DE filter or a 96sft cartridge filter. Cartridge filters can be oversized without limit; DE and sand filters cannot.

The 'real' flow rates for filters are the ones listed for public pools:

sand => 15 gpm/sft
DE => 2 gpm/sft
cart => 0.375 gpm/sft

The Superflo pump may, or may not, be too big. Two questions:
1. What is the exact model of the pump, and what are the electrical ratings on the motor?
2. Are you handy enough to take the pump apart, and re-assemble it?

Pentair Superflo model # sf-n1-1a 1 hp pump .....

voltage=115/230
full load amps=14.2/7.1
hp=1
sf=1.25
sfhp=1.25

not sure if any of that helps..? Yes , handy enought to do what needs to be done.

Thanks

OK. That model is the 1hp Up-rate standard efficiency Superflo.

Pentair info page
Manual

Here's an option:

Pentair 350088S with SWTCH SQFL 3/4 HPF 1A 60-Hertz 2SP ALMD Motor Package
Pentair 355067 Impeller Assembly Replacement Pool and Spa 1 HP Inground Pump
Seal and gasket kit at A1PoolParts.com

Check the manual, and confirm, but I believe those are the right parts to convert your pump from a standard (low) efficiency 1HP motor to a high efficiency 2spd motor - for around $250.

You'll want to run on LOW all the time, except when priming, vacuuming or backwashing. LO moves about 1/2 the water that HI does, but uses about 1/6 the electricity. Your flow will be much better matched to your pump -- and your water may be clearer as a result. Your electric bill should go down a bunch!

A couple of tips:

1. If you have a timer, you may have to put a check valve in the piping just ahead of the pump, so it doesn't loose prime when it's turned off. The Jandy check valve is available from Amazon and is a good choice.

2. You'll need to watch your backwash discharge. If you find sand coming out with the backwash, you'll need to put a valve on the discharge (a cheap PVC ball valve is fine) and throttle it to slow the flow. LO may be too low to fully backwash, but HI may be too high.

I'm actually thinking of upgrading to a hayward 24 or 27 inch sand filter...I looked at the 24 inch and it seems to be enough flow to handle the Pentair pump...any thoughts?

Upgrading filters is ALWAYS a good idea. Even so the 2 speed works better with sand filters.

The slower the flow, the better the filtration with sand. 8 hours on LO will produce higher water quality than 4 hours on HI . . . and will use less than 1/2 of the electricity!

With the larger filters, you won't need a discharge throttle valve, but will definitely need to backwash on high.

Another question ...should I plumb the pool with 1 1/2 or 2 " pipe? ....what is the benefit of 2"if any beside less pressure?
Again...thanks for the help

Before I try to answer ?'s like that, complete the pool equipment form: http://pool9.net/pf-equip-form

In the notes, include info about extra equipment, number of skimmers, and number of returns.

Form completed.

.