Forum: --cleanup--

I have not been able to figure out how to adjust the cam on the CVA-24T 180° Actuator. It currently goes slightly past the close position on one of...

Hi Does anyone know how or if its possible to have the goldline gl235 solar controller requeest a speed increase from an Ecostar variable speed...

Hi everyone, My wife and I have just replastered our pool. It has a blue/back 50/50 quartz finish. It should be filled by the end of the day...

Hello everyone, I just purchased a brand new home with a salt water pool. The Pool is 25,000 gallons, and has a pool pilot digital nano , in...

All equipment is Hayward; 2 speed pump, PS-8, heater, sense & dispense, etc. FOUR electrically controlled valves. Hayward PS-8 documentation is...

Greetings all I have recently bought a home that has a vinyl in ground pool that I am guessing is about 30,000 gal, and I am busy learning all...

I got back from the holidays to find my pool pump was blown. In pulling it apart for an initiate check, I found some problems. a) the pump is...

I have an inground qunite pool that just began loosing about an inch of water per day. I've done the bucket test comparisons - only loosing water...

Hello everyone. This is my first posting to the forum. Thanks for having me. My wife and I are getting our pool replastered this week. It is...

I bought a new Pentair handheld remote to replace an older model remote. I tried pairing the new remote and it doesn't connect to my Intellitouch...

Hi, I don't know much about my pool equipment but I have a Jandy Aqualink RS4 and the filter pump will not turn off. I wen't outside to the...

I have a CVA-24T actuator with 180° rotation on my 3-way Jandy valves and they to not go back to exactly 0° or to 180° when actuated. Both valves go...

We have major wall corrosion behind our vinyl liner (in-ground pool). I've pulled away much of the liner and can see the bad rusting/corrosion. ...

Hi, I'm looking at an inground liner pool (18x36) with stone coping. It will be salt water pool and will be rectangular and the only non-stock...

My old 3/4 hp pump had died after many years of service. My pool is 16x32, 3 ft deep to 6 ft deep. The old pump is a 3/4 hp marathon. I live in...

We just moved into this house and it has a pretty nice screened-in pool behind the house (Central Florida). Its an in-ground pool with a little...

I am looking at purchasing a AG pool this year, within the next 2 months and I have been looking around and found several. I am wanting to get a 27'...

I was going to build last year at this time, but like most others, the equity was not available in my home! We are going to make another attempt and...

I recently purchased an Intermatic Multiwave PE653RC along with their 24v valve/pump switch (P4243ME). I have not installed it yet. After reading the...

I recently installed my 14 X 30 inground fiberglass pool. Last night, there was a pretty bad storm and I'm guessing that a lot of rain fell. When I...

I have a major leak. The pool shell is not the issue but rather the main skimmer line and drain line appears to be compromised. The pool pump would...

Hello all--- we had a pool installed two months ago with a jandy in-floor pool cleaning system. in order to maintain adequate pressure in the system,...

Wrap the thread 3 to 4 times tightly with teflon tape. Then apply a bead of GE Premium Waterproof Silicone (Kitchen, Bath, Plumbing). Tighten the...

I take care of a commercial pool with 56,000 gal. of water. Currently, we chlorinate with 3" dissolvable tablets in constant feeders. The problem...

I have a Hayward 350,000 BTU gas pool heater that was purchased when we renovated our house but was never connected. It is just taking up space in...

I'm refurbisihing me 25 year old pool. I bought the house 15 years ago. Just had the plaster re-done and want to replace my obsolete Mytilus Pacfab...

Hello, I live in Arcadia California and every week I clean this pool it has salt piled up in the spa and in piles at the bottom of the pool. The...

I had a motor go out on my pool pump and bought a rebuilt. No matter what I did the pump with the new motor would not prime. I tried everything in...