Questions about all sorts of pool equipment that is electronic, or controlled by electronics
CPHVLEDS100 Jandy LED lights first one was dead within 3 years, the 2nd one dead on open in year 4. Hardly ever used. Salt water pool LED's...
How do I trouble shoot the following error code? "Possible Front board service condition or unit not correctly wired to 115 VAC"
Hello all, my first post here. I just installed a Starite Maxitherm heater where an ancient Teleydne was. The Starite can be connected to a Jandy...
Hi I replaced my aging Jandy Ji8000 with the new iAqualink bundle. Now the iAqualink is my only scheduling and control device (outside of the...
Hi, I am happy I found this great forum. Hope you guys apologize my English; I am German but live in Florida since a while, still working on my...
We have an L-shaped vinyl inground pool with attached spa, which is about 15 years old. It therefore has two separate pumps -- a main pump and one...
Hello, I am new to the forums. I have a Jandy Aqualink 6700 REV C with RS8 controller. I recently had solar heating panels installed and had a JVA...
Just replaced my Jandy/Zodiac Aquapure control board with upgraded model so I can use iAqualink. Simple enough. Had the PDA version, pre 2007. Set...
Hi, My old Hayward system fired during lightning. Have lightning rods now and surge protection now. What is the best system? I like the...
I have a 2 y.o. salt water pool with Pentair Easy Touch panel (and remote). I would like to look into replacing my pool and spa lights with the...
Had a power surge of some origin. Have replaced fuses and control board and have now nailed it down to an intermittent/faulty j7 connector...
Hi, I have a LM2 24 and I have an issue with the power board. Specifically, the R26 resistor is burnt and the C19 cap looks about ready to go, if...
Just wondering if anyone has added one of these to their pool? I wish my pool was plumbed for it but it's not and during the hot AL summers I'm...
I have an Aqua logic control that wont keep time, I have to manually change the day and time everyday, could not find any backup battery and the pool...
i would like to hook this stuff up to a controller . maybe wireless . basic ,right now I just have 4 contactors .filter pump .waterfall pump....
New here but would like to know if anyone has used a uv system?
I have an Aquacal pool heater that runs and doesn't cool. It happend over a year ago and we had a repairman come out to fix it (it took him 10 mins)....
I have 3 pole lights around my pool that have stopped working. I ran a diagnostic on my Aquling RS8 and it showed the solar Aux3 circuit "open"...
We replaced our 2speed pump with a pentair super flo 2speed pump. Our existing wires were 2 blue hot and 1 green ground. We plugged the hot in and...
Early Spring we converted to a Jacuzzi Saniclear 40 salt system. The box that is on the house gets VERY hot. This morning when I turned it on it...
We are considering a pool alarm (like the one where water disturbance sounds an alarm in case a child falls in). However, I've reviewed many of...
Hello All, I'm new to the Salt Water Pool ownership and had a few questions about the Hayward OnCommand System currently installed. It seems to...
Looking for a little Info. I was given a brand new Hayward OnCommand controller and a Hayward 11KW spa heater. I have not recived it yet, it is...
my poolman replaced a relay and then when a program didn't work properly, he deleted the memory. we restarted the rs8 and now the programs work...
Does anyone know if the temperature can be calibrated, or does it even matter for optimum generation
Given all the troubles with the Aquarite and others control boards, has anyone ever developed/built/invented a simple, sort of manual control for the...
Long-time pool owner.... new to the forum. I just had a Zodiac iAqualink controller installed. It replaced a 16-year-old Aquadyne Mini panel. The...
I just had my liner replaced 30 days ago after 1.5yrs due to liner seam failure.13,700 gal Originally used all bioguard stuff that the pool store...
I have checked the wiring and installation, all is good there. Can't get the Aquapure ei to connect to the iaqualink. Any suggestions?
We have had the above equipment for about 8-9 years. I have always had to RE-Enable the Aqualink at the heater after a power outage because it would...
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules