Forum: Above-Ground Pool Construction & Repair

Looking at the Whispering Wind with a 6' deep end and buried into the ground. I’m worried about putting the pool into the ground. My installer...

My above ground pool broke 2 support posts at the bottom rail and blew out the liner and damaged the wall also.I bought it from Namco ,It is only a...

Okay, got the liner smoothed pretty good last night and got about 1.5 feet of water in. Went out 9:30am to plan the next round and I notice some...

Which way goes toward's the water the smooth side or the textured side? Tx Yves

I have been trying to install a 18ft x 48" pool over the last few weeks, needless to say nothing but problems...first I dug it out 6 inches (my...

Our 1 year old solar cover has split on a seam. While I am awaiting a replacement from the company, I wanted to try to glue the pieces together. I...

I am looking for a Solar Reel to mount to my fence or deck permanently to roll up my solar bubble cover. It's 18' x 40' and heavy. I have seen...

Okay, how the heck to I get these creases and folds out? I have a J hook liner, so I can't just pull the excess up the wall. Should I work them out...

i just bought a 1700 gallon AG pool (12'x3'). its not very big but i am using it for therapy. i have to put it in my garage because i live in an...

Anyone have one of the Hayward X-stream cartridge filters? Mine is brand new and it's making noise. It makes this squekay grunting noise because I...

Thanks for prompt replies on a prev post. Couple of add'l questions: 1. Do the bubbles on a solar cover face up (sky) or down (water) on the...

I purchased a solar cover and reel for an AGP (oval 12 x 18). From what I've read it's recommended that the reel should be installed at the beginning...

How long should I run my pump for a 33' round ag pool at 1/2 hp on a 26" filter.Thanks, Sharon

I have a question about leveling the sand. Do you make a 2" high border in a 20 ' diameter circle (for a 18' doughboy) and level it and the screet...

Tonight our liner ripped big time. The pool is really old and right next to our house. The water almost flooded our basement so we either want to...

To heat a pool that has a volume of 13,500 gallons, I'm hearing 100,000 and 150,000 btus. Our neighbor has a 17,000 gal. pool, and was sold a 100k...

My husband and I are installing an 18' round. We have been told to use either regular mason's sand or limestone sand to cover the dirt. We have the...

I needed to drain my pool due to algae this spring. I drained (18,000 gal.), cleaned, then started to re-fill. I dont know how I missed it, however,...

Had the pool installed this spring and just pluged it in to a 110 gfi with 10 guage extention cord. The pump is a 2hp not sure of the make but here...

I'm sooooooo sorry for all of these questions, but I bet this one will be easy for you pros out there. Our pool is 15x30x52" and I think it's about...

does it hurt the water if you leave your solar cover on for days at a time . someone told me that you have to take it off during the day or you're...

I have a pool that is approximately 12X18 feet. AG. I have the Astral 150 Cratridge Filter. I recently bought a new pump, a 1.5 HP. Is it...

We need to replace the bottom wall channel pieces from the used Esther Williams pool that we bought. I called the Delair group directly and they...

We are getting ready to put up our pool. We went with the 33' round Emerald Isle from Artesian. I think I understand the directions ok but Im a...

Hello, new to the forum, second year with a pool, lots of lessons learned. I have a brand new 15' genfoam pool (Walmart Intex vinyl type), 42" deep...

Hey all, I'm in the middle of building my AG 15x30 Quest. I thought I'd share some thoughts on the install and maybe ask some questions. First...

When my husband leveled the ground, it was level except for minor bumps/tread from the bobcat tires, etc......When he took down the pool from the...

I'm installing a 15 x 24 used pool. I've poored my cement sidewalk "support" yesterday as per the manuf. instruction. I will remove the forms...