Forum: Pool Equipment & Operations

I purchased a Jacuzzi JCQ 420 pool filter and have found that the filter cartridges keep failing. I would like to purchase replacement cartridges...

Hi all, My pool pump is going on 30 years old. This year the cover to the electrical hook up rusted away. The casing on the motor is pretty rusty...

SO i just bought a new Hayward Super pump 700. Had an electrician hook it up. It starts up at a normal high speed then kicks down to a slow speed,...

Hi, Recently I was talking with an acquaintance who also has an inground pool. She was telling me she had to replace the sand in her filter because...

Hi, I noticed this morning that my pump has become noticeably louder, and higher pitched; and I'm wondering if there's anything I can do,...

I am replacing my inline chlorinator (the cylinder type you drop tablets into.) My question is, because it must remain upright, when screwing in to...

Help. I am trying to find the correct basket for my Jacuzzi pool pump. Everything I have found seems to have different dimensions. Is the Jacuzzi...

We are planning on replacing our 21 year old TR 60 Sand Filter this season along with the multi-Port. We have our pool covered for the winter. Plan...

Looking for a new salt water filer. I currently have a 20 year old cracked Hayward DE. My pool is 13Kgal I know my Hayward DE was real good but...

So all around the edges my maaco pool cover is wearing due to a lip, especially corners. Can I use waterproof gorilla patch & seal tape vs. buying...

#1 I have to replace my current pool pump, a Hayward 3400VSP, as the drive has went out again (2nd time) and I have already replaced 4 motors. The...

I have a Hayward 3400VSP pool pump. I have went through 4 motors in last 6 years. I am unsure if a motor should only last this long, or if they are...

I'm in San Diego. Water evaporation is expensive. My water bill last year was $750 for 2 months I think I've cut it in half by doing bubble...

Is this normal. In Spa mode only I'm pulling 20 psi. When I put pool and spa I'm pulling 30 psi

Polaris Floor Cleaner does not come on in normal mode When I put it in service mode the motor does turn on but the Polaris never moves

Can someone recommend a good above ground pool pump? I don’t want to waste money and want a really good one. I have a 26ft round above ground and...

The original was definately bad, measuring 0 ohms. I replaced it with a Laars kit and hooked everything back up. Still no ignition but the ignitor...

I have a K3475 STA-RITE C76-59P P4 SERIES TANK BODY. I replaced my pump motor (C48L2PA103A3) with this model ordered from Amazon:...

OEM is over $100. Are there any suitable aftermarket igniters available? I found an OEM on amindemoa.com for $35 but I suspects it's fishy. Thanks.

I can't get the skimmer weir door to stay, every time someone jumps in the pool making waves the door comes undone and floats out in the pool. I'm...

We moved into a new house this week that has a 24' round above ground pool that has been buried. The current system is a sand filter with a 3/4 HP...

I had to replace a PIA saltwater device by cutting it out between the adjoining 2" pvc pipes and replaced it with 2" pipe along with a PVC...

Hello all - ok ..so Ive been on a mission to locate my trouble. Im getting a fairly good prime but a lot of air bubbles in the return jets &...

Pool pump died after only 8 years in NJ... As all my Jandy equipment has early deaths. Any suggestions? I have a 40k salt water pool. Also costly...

This year our heat pump seems to only be heating the water about 2 degrees in an 8 hour run cycle, it usually does better than this. The filter is...

Hello Everyone, I need some assistance with my pool plumbing. The original installer of this pool placed the filter way too close to the fence,...

Hello- just curious if anyone has had lasting success with the adhesive patches vs using the patch/glue method? Whats best? Thanks!

I have programmed 5,6, and 7 to run a schedule. I don’t see the power draw on the display. I see PSI instead. I saw the power draw when running it on...