Leak from Filter

[donfranko]

I have a Hayward DE 7220 filter (3 years old!) that just started leaking from the joint where the top meets the bottom. It looks like the metal strap is is completely tightened.
Any idea's on probable causes? I can do without a major replacement bill.
thanks

[waste]

Don, how are things in Mahwah, other than a leaky filter?:D Sorry you're having filter issues again, I had hoped the cleaning of the grids would have kept you good for the summer!:(

I'd open the filter and check the o-ring! Sometimes just cleaning the sealing areas on the filter and rinsing and lubing the o-ring will do the job:cool: Otherwise (unless you see a problem with the sealing areas on the tank itself) a SP 2400 K (tank o-ring) replacement should fix it :) ( ~ $ 25)

If you open it and have any questions, I check this site (first!) almost every night:cool:

[donfranko]

Thanks. Looked at it today and I think I need a new clamp assembly + an O ring. $250!

Some sticker shock on the price of a clamp and also very surprised it would fail this quickly. Any others have problems with this clamp?

[waste]

Don, can you tell me how the clamp has failed? I've never seen the clamp itself fail, but sometimes the threads on the nut or bolt can strip -- HOPE that it's the sleeve nut, they should run ~ $30. Before you go and blow $250:eek: , let me know what's wrong with yours - I may have the part you need floating around ;) (for some reason, they don't sell the bolts:confused: but I try to salvage unavailable, or hard to come by, parts when I can:)

Please let me know where the problem is and I'll try to go without a huge outlay of $.

[Vinyl_Guy]

Take it to a local machine shop.

They might be able to machine you a part for under the cost of new ones. Especially if it's just a threaded part or bolt, or both. While $250.00 doesn't go a long way these days it's still a fair amount of money. . The "band" it self would cost too much to fabricate a new one.

These filter bodies can be funny. Try re-seating it a few times. Often times you might be trying to "squeeze" the two body halves too much with the clamp assembly itself. What happens is, if the the "O" ring is compressed entirely via the clamp band it can "roll" and become malformed. Try disassembling it, and when you put the two halves together some how (it's a pain) try pushing them together evenly with some weight. I used to remove the gauge or bleeder on top (as to not damage it) and sort of bearhug it the top half down onto the bottom. Make sure it begins to seat evenly around the circumference of the halves . You can't possibly push it all the way together but make sure it begins to "close" some what before using the band clamp to completely seal it. You might need help, one person applying pressure to the upper body half, and the other putting the clamp assembly on. It's going to want to "pop" up while you putting manual pressure on it.

One other thing. The clamp itself is in the profile of the protrusion where the "O" rings sits on the body. Make sure it didn't get splayed outwards. This can happen from continually using the clamp to pull the body halves together from their most separated positions. Put the filter together with out the O ring in it so that it seats flush, then hold the clamp up to it and make sure it still follows the profile of the protrusion. If not, squeeze it in a vice, carefully and in small increments till the areas that have become "splayed" out ward are more in profile with the protrusion.

There also might be a notch in each segment of the filter halves, in the the area that the "O" ring sits. Make sure these are aligned. For the life of me I don't know why it makes a difference, but sometimes it does.

I'd try to exhaust all possibilities, even just re-seating it again. You might have had the "O" ring become malformed or "rolled" the times you've tried so far, one more time might do it.